Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Drafting Standards, GD&T & Tolerance Analysis

Jacob Cheverie
  • Locked
  • Question Question
Validity of Composite Positional Tolerance
Replies
10
Views
347
Jacob Cheverie
Jacob Cheverie
Mecha_nik
  • Locked
  • Question Question
Surface Roughness Filter Designation
Replies
0
Views
140
Mecha_nik
Mecha_nik
Rwelch9
  • Locked
  • Question Question
DRF for a pattern of holes
Replies
6
Views
215
Rwelch9
Rwelch9
Alexane
  • Locked
  • Question Question
Surface perpendicularity - A beginners question
Replies
3
Views
152
drawoh
drawoh
axym
  • Locked
  • Question Question
Tolerance Zone Extent
2
Replies
39
Views
1K
Burunduk
Burunduk
dthom0425
  • Locked
  • Question Question
Origin of Measurement for Pattern of Holes
Replies
8
Views
807
dthom0425
dthom0425
dthom0425
  • Locked
  • Question Question
DRF for module with pins
Replies
9
Views
222
3DDave
3DDave
AMontembeault
  • Locked
  • Question Question
Surface Profile and Size
4 5 6
Replies
103
Views
5K
Burunduk
Burunduk
Rwelch9
  • Locked
  • Question Question
True geometric counterpart for a CF cylinder.
Replies
19
Views
597
Rwelch9
Rwelch9
SeasonLee
  • Locked
  • Question Question
Is it valid to have a Free-State symbol here?
2 3 4
Replies
65
Views
3K
SeasonLee
SeasonLee
Rwelch9
  • Locked
  • Question Question
True position of a slot
Replies
8
Views
3K
Rwelch9
Rwelch9
Tarator
  • Locked
  • Question Question
Does anyone understand "spines" of a regular FoS per ASME Y14.5.1M-1994 (R2012)?
2
Replies
25
Views
434
greenimi
greenimi
Rwelch9
  • Locked
  • Question Question
True position callout
Replies
4
Views
262
chez311
chez311
Sa-Ro
  • Locked
  • Question Question
Drawing verification
Replies
15
Views
412
Sa-Ro
Sa-Ro
Sa-Ro
  • Locked
  • Question Question
Pattern of holes as Secondary datum
Replies
17
Views
610
Sa-Ro
Sa-Ro
Burunduk
  • Locked
  • Question Question
A minimum material envelope as a datum feature simulator
2
Replies
23
Views
583
Dean Watts
Dean Watts
Burunduk
  • Locked
  • Question Question
Plane surface datum feature MMB located basically from a higher precedence datum
2
Replies
31
Views
853
Dean Watts
Dean Watts
TJ81
  • Locked
  • Question Question
More Details Requested.
Replies
1
Views
54
drawoh
drawoh
Sa-Ro
  • Locked
  • Question Question
Profile tolerance for location control
2 3
Replies
57
Views
802
Sa-Ro
Sa-Ro
xnabrar
  • Locked
  • Question Question
REINFORCEMENT PAD.
Replies
2
Views
151
xnabrar
xnabrar
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top