Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Drafting Standards, GD&T & Tolerance Analysis

BrysonRD
  • Locked
  • Question Question
-100, -300, and -500 Drawing Levels
Replies
6
Views
463
jassco
jassco
3DDave
  • Locked
  • Question Question
Would you like to play a game?
Replies
0
Views
148
3DDave
3DDave
GravyBagel
  • Locked
  • Question Question
Angled/Extended Tolerance Zone
Replies
5
Views
400
3DDave
3DDave
cmart
  • Locked
  • Question Question
GD&T - Bent Tube End Squareness
Replies
11
Views
2K
Burunduk
Burunduk
GravyBagel
  • Locked
  • Question Question
Slot GD&T
Replies
2
Views
361
GravyBagel
GravyBagel
Tegguy
  • Locked
  • Question Question
DRF Change Impact Example
Replies
5
Views
377
Tegguy
Tegguy
Burunduk
  • Locked
  • Question Question
nX, Detail Views, and the INDIVIDUALLY note
Replies
9
Views
627
Burunduk
Burunduk
Oadriusa
  • Locked
  • Question Question
Is this usage of 2x angularity and parallelism correct?
Replies
16
Views
989
Burunduk
Burunduk
sendithard
  • Locked
  • Question Question
Thank you
Replies
16
Views
587
3DDave
3DDave
dogbural
  • Locked
  • Question Question
how to read hole tolerance
Replies
2
Views
203
Wuzhee
Wuzhee
Myint Mo
  • Locked
  • Question Question
Drawing Resources For Plastic Manufacturing
Replies
2
Views
384
gb2835
gb2835
Pupsocket
  • Locked
  • Question Question
working with multiple profiles of surfaces
Replies
8
Views
469
Pupsocket
Pupsocket
sendithard
  • Locked
  • Question Question
Fig. 8-27 2009 why is Datum B required if it is a valid callout
Replies
16
Views
506
Burunduk
Burunduk
David G
  • Locked
  • Question Question
Basic question with ISO 13920 on how to measure a skewed plate
Replies
0
Views
5K
David G
David G
jbird68
  • Locked
  • Question Question
What is the correct callout for number of instances
Replies
14
Views
2K
ewh
ewh
sendithard
  • Locked
  • Question Question
Can you apply MMB with orientation tolerances?
Replies
5
Views
544
Belanger
Belanger
sendithard
  • Locked
  • Question Question
Runout callout with a datum to itself
Replies
5
Views
1K
pmarc
pmarc
brwalker145
  • Locked
  • Question Question
Parellelism Against A Complex Surface
2
Replies
30
Views
1K
axym
axym
mthomsen
  • Locked
  • Question Question
Which Pipe Is Higher
Replies
0
Views
115
mthomsen
mthomsen
PetkovStoyan
  • Locked
  • Question Question
GD&T with general tolerances between datums
Replies
14
Views
578
Wuzhee
Wuzhee
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top