Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Drafting Standards, GD&T & Tolerance Analysis

Gopinath K
  • Locked
  • Question Question
difference between composite and multi segment pos tol in asme y14.5 2009
2 3 4
Replies
76
Views
3K
3DDave
3DDave
enggasw
  • Locked
  • Question Question
GD&T Basic needs in aspect of application.
Replies
5
Views
355
3DDave
3DDave
Enrico Urru
  • Locked
  • Question Question
Perpendicularity
Replies
13
Views
729
Enrico Urru
Enrico Urru
PetkovStoyan
  • Locked
  • Question Question
Measuring runout on a shaft relative to two datum surfaces
2 3
Replies
40
Views
3K
PetkovStoyan
PetkovStoyan
Gopinath K
  • Locked
  • Question Question
minimum wall thickness of the four holes to the O.D. of the part.
Replies
8
Views
520
Gopinath K
Gopinath K
kwyjibo1
  • Locked
  • Question Question
Perpendicularity of surface - long edge vs short edge.
Replies
16
Views
808
flash3780
flash3780
Gopinath K
  • Locked
  • Question Question
Axis to Axis calculation
2
Replies
28
Views
981
greenimi
greenimi
nik007
  • Locked
  • Question Question
Correctness of the gd&t symbol
Replies
3
Views
262
flash3780
flash3780
flash3780
  • Locked
  • Question Question
Projected Tolerance Zone with Slot Position
Replies
6
Views
787
flash3780
flash3780
nik007
  • Locked
  • Question Question
Significance of the symbol
Replies
13
Views
2K
pmarc
pmarc
RCor
  • Locked
  • Question Question
How best to add GD&T to ensure symmetry
2
Replies
20
Views
2K
jassco
jassco
dogbural
  • Locked
  • Question Question
tolerance on shaft against mating bearing set tolerance
Replies
3
Views
316
geesaman.d
geesaman.d
Woosang
  • Locked
  • Question Question
Can Symmetry tolerance symbol be applied to cylindrical features? (both ASME and ISO)
Replies
3
Views
435
Ryan6338
Ryan6338
Gopinath K
  • Locked
  • Question Question
can we use total runout with projected tolerance zone?
Replies
5
Views
577
axym
axym
JacquesBeaudoin
  • Locked
  • Question Question
Simultaneous requirements for patterns
Replies
18
Views
1K
axym
axym
Burunduk
  • Locked
  • Question Question
DML straightness material condition modifiers and relation to position/orientation at MMC
2 3
Replies
41
Views
2K
Burunduk
Burunduk
Ryan6338
  • Locked
  • Question Question
Best way to indicate simultaneous profile requirements for a group of features on sheet metal.
Replies
18
Views
829
pmarc
pmarc
supergee
  • Locked
  • Question Question
Simplified representation of gears and chains
Replies
6
Views
501
cowski
cowski
Ryan6338
  • Locked
  • Question Question
ISO GPS Reciprocity
Replies
4
Views
949
Ryan6338
Ryan6338
3DDave
  • Locked
  • Question Question
Interactive Fixed Fastener / Projected Tolerance Demonstration
Replies
2
Views
313
3DDave
3DDave
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top