Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Drafting Standards, GD&T & Tolerance Analysis

sendithard
  • Locked
  • Question Question
Simultaneous requirement confusion
Replies
3
Views
890
axym
axym
dogbural
  • Locked
  • Question Question
Drawing tolerance
Replies
10
Views
404
Wuzhee
Wuzhee
3DDave
  • Locked
  • Question Question
Interesting drawing
Replies
15
Views
588
Qcprick63
Qcprick63
Burunduk
  • Locked
  • Question Question
End face as secondary datum feature for runout - redundant?
2
Replies
26
Views
925
3DDave
3DDave
Daren Samy
  • Locked
  • Question Question
Pump Bearing Fits confusion
Replies
6
Views
339
Daren Samy
Daren Samy
straightline101
  • Locked
  • Question Question
Multi Axes defining a Plane
Replies
9
Views
889
drawoh
drawoh
supergee
  • Locked
  • Question Question
Abusive use of Continious feature?
Replies
9
Views
664
CheckerHater
CheckerHater
dthom0425
  • Locked
  • Question Question
Position Refinement
Replies
2
Views
251
3DDave
3DDave
sshosseinee
  • Locked
  • Question Question
Precision
Replies
14
Views
488
Burunduk
Burunduk
Radius1
  • Locked
  • Question Question
GD&T position Mutiple segment - Calculating min and max span of bolt holes.
Replies
16
Views
988
Belanger
Belanger
3DDave
  • Locked
  • Question Question
Composite tolerance
Replies
7
Views
262
Burunduk
Burunduk
Wuzhee
  • Locked
  • Question Question
Composite lower segment not related to datums - Figure 11-35
Replies
1
Views
162
Burunduk
Burunduk
Bux1986
  • Locked
  • Question Question
Controlling depth of separate counterbore. Bottom surfaces act as surface for alignment
Replies
13
Views
607
Burunduk
Burunduk
Jay8833
  • Locked
  • Question Question
Concentricity with common axis A-B?
Replies
16
Views
902
Garland23
Garland23
Burunduk
  • Locked
  • Question Question
No Y14.5 version referencing Y14.5.1-2019. And, what is the "single solution"?
2
Replies
21
Views
2K
SeasonLee
SeasonLee
sendithard
  • Locked
  • Question Question
Offset keyway datum UAME must remain parallel to primary axis datum A confusion
Replies
13
Views
1K
3DDave
3DDave
MToomey
  • Locked
  • Question Question
Bolt Circles - Relative Clocking
Replies
11
Views
1K
3DDave
3DDave
Radius1
  • Locked
  • Question Question
Position Tolerance and MMC with Multiple Datum References
Replies
6
Views
406
3DDave
3DDave
onekotan88
  • Locked
  • Question Question
Bilateral unequally disposed profile - actual measurements
Replies
2
Views
769
onekotan88
onekotan88
Radius1
  • Locked
  • Question Question
Do I have the correct Idea for Position tolerance
Replies
6
Views
460
Radius1
Radius1
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top