Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Drafting Standards, GD&T & Tolerance Analysis

Goppinath
  • Locked
  • Question Question
How do you apply datum scheme to curved and irregular surfaces in engineering drawings?
Replies
1
Views
179
3DDave
3DDave
CLos
  • Locked
  • Question Question
GD&T of Dodecahedron Approach
Replies
2
Views
190
CLos
CLos
TopPocket
  • Locked
  • Question Question
Aligning a dimension to a datum axis?
Replies
14
Views
1K
cr7
cr7
lowerp
  • Locked
  • Question Question
datum feature question
Replies
6
Views
215
Burunduk
Burunduk
TopPocket
  • Locked
  • Question Question
Perpendicularity is Perplexing
Replies
3
Views
325
3DDave
3DDave
Burunduk
  • Locked
  • Question Question
STOCK, Rule#1 & geometric tolerances
Replies
9
Views
598
3DDave
3DDave
freerangequark
  • Locked
  • Question Question
CTF (Critical To Function) indication for a dimension
Replies
4
Views
1K
3DDave
3DDave
jnelson33
  • Locked
  • Question Question
GD&T - Edge-Bonded Gaskets
Replies
4
Views
522
jnelson33
jnelson33
Joel Lapointe
  • Locked
  • Question Question
Asymetrical profile tolerance must match adjacent recess diameter tolerance!
Replies
2
Views
174
BiPolarMoment
BiPolarMoment
etrud011B
  • Locked
  • Question Question
Help finding a CAD sharing program
Replies
6
Views
284
3DDave
3DDave
Andera
  • Locked
  • Question Question
Second case, profile callout
2 3
Replies
40
Views
1K
Burunduk
Burunduk
PetkovStoyan
  • Locked
  • Question Question
GD&T of extruded part with irregular profile
2
Replies
27
Views
932
PetkovStoyan
PetkovStoyan
nry67
  • Locked
  • Question Question
Aligment
Replies
5
Views
186
Burunduk
Burunduk
aniiben
  • Locked
  • Question Question
How to interpret those dimensions ?
Replies
17
Views
2K
nry67
nry67
y2k_o__o
  • Locked
  • Question Question
Proper way to dimension a seal groove path around an enclosure
Replies
4
Views
1K
3DDave
3DDave
Patton3660
  • Locked
  • Question Question
Having a Joint Table for Weldment Drawing
Replies
2
Views
228
3DDave
3DDave
New to this
  • Locked
  • Question Question
GD&T for bolted flange of two rotating parts
Replies
6
Views
3K
Burunduk
Burunduk
Burunduk
  • Locked
  • Question Question
MMB datum feature simulators used in a restrained condition?
Replies
14
Views
1K
3DDave
3DDave
ejsam
  • Locked
  • Question Question
How can I convert these linear dimensions to GD&T?
Replies
11
Views
424
Burunduk
Burunduk
Burunduk
  • Locked
  • Question Question
AME of a contoured or planar feature?
Replies
4
Views
244
CheckerHater
CheckerHater
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top