Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Drafting Standards, GD&T & Tolerance Analysis

durablack2
  • Locked
  • Question Question
HOLE AS PRIMARY DATUM OR NO?
2
Replies
25
Views
4K
Sem_D220
Sem_D220
rmetzger
  • Locked
  • Question Question
cosmetic specifications to indicate a acceptable level of defects
Replies
1
Views
578
AndrewTT
AndrewTT
handleman
  • Locked
  • Question Question
Runout for a cylinder with a flat face
Replies
5
Views
386
pmarc
pmarc
OmarEn07
  • Locked
  • Question Question
Rule #1 of Y14.5
2
Replies
23
Views
955
djhurayt
djhurayt
Wunderbear
  • Locked
  • Question Question
Using statistical tolerance <ST> symbol to indicate design intent
Replies
8
Views
2K
chez311
chez311
axym
  • Locked
  • Question Question
Combined Controls Extension
2 3
Replies
55
Views
2K
semiond
semiond
erik3000
  • Locked
  • Question Question
Control the angle of a theoretical line between two holes relative to a mating part on assembly
Replies
4
Views
293
erik3000
erik3000
DavisL
  • Locked
  • Question Question
Should An Interface Control Drawing (ICD) Be One-Sided or Two-Sided?
Replies
7
Views
373
MintJulep
M
aniiben
  • Locked
  • Question Question
Tangent plane modifier (legal usage—not functional one in my shown case)
2
Replies
34
Views
1K
DeanD3W
DeanD3W
K_Ho
  • Locked
  • Question Question
Writing Datum After A Basic Dimension
Replies
11
Views
395
semiond
semiond
Kedu
  • Locked
  • Question Question
Flatness on both sides of a feature of size
Replies
14
Views
473
Kedu
Kedu
pmarc
  • Locked
  • Question Question
True Profile Definition
5 6 7
Replies
130
Views
3K
semiond
semiond
aniiben
  • Locked
  • Question Question
Rotation
2 3
Replies
58
Views
735
chez311
chez311
kego
  • Locked
  • Question Question
How to specify dowel pin locations
Replies
16
Views
2K
semiond
semiond
Belanger
  • Locked
  • Question Question
Circled Y
Replies
1
Views
98
powerhound
powerhound
AndrewTT
  • Locked
  • Question Question
question on restrained part figure
Replies
11
Views
276
AndrewTT
AndrewTT
chimps12
  • Locked
  • Question Question
GDT Dimensioning method for 2 datum holes that break thru a wall
Replies
15
Views
751
semiond
semiond
LargeNCharge86
  • Locked
  • Question Question
Min/Max vs. Limits vs. Plus/Minus
Replies
10
Views
714
JR97
JR97
Hugh Man
  • Locked
  • Question Question
Surface profile not normal to DRF
Replies
6
Views
204
chez311
chez311
erik3000
  • Locked
  • Question Question
Curved slot continuous feature
Replies
2
Views
406
3DDave
3DDave
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top