Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Drafting Standards, GD&T & Tolerance Analysis

efulm4444
  • Locked
  • Question Question
Best way to call out surface finish after machining vs after alodine coating
Replies
9
Views
2K
drawoh
drawoh
TopPocket
  • Locked
  • Question Question
Line Profile of Bent Bar to be inspected with Envelope Gauge
Replies
18
Views
1K
Ryan6338
Ryan6338
edw.jack23
  • Locked
  • Question Question
Offset rotation between Datums
Replies
13
Views
680
greenimi
greenimi
M.B.
  • Locked
  • Question Question
Nut face runout / perpendicularity to thread - inspection strategies
2
Replies
20
Views
2K
supergee
supergee
Tmoose
  • Locked
  • Question Question
un-referenced datums revisited
Replies
13
Views
766
supergee
supergee
VN1981
  • Locked
  • Question Question
Help with Recommendation for Basic Drafting Tutorials?
Replies
2
Views
408
greenimi
greenimi
Diametrix
  • Locked
  • Question Question
A ball and GD&T
2
Replies
23
Views
1K
Belanger
Belanger
J-Hendry
  • Locked
  • Question Question
Different interpretations of the DATUMS - Which is correct?
Replies
13
Views
1K
jassco
jassco
eng123mech
  • Locked
  • Question Question
ASME Standard for Inspection of an Assembly Drawing
Replies
12
Views
2K
jassco
jassco
elinah34
  • Locked
  • Question Question
ISO standard - A parallelism of a plane to an axis
Replies
8
Views
715
elinah34
elinah34
DesEngineer4
  • Locked
  • Question Question
Detailing Check List
Replies
2
Views
448
Belanger
Belanger
TopPocket
  • Locked
  • Question Question
Is there a modifier to make an ISO Datum be defined like an ASME Datum?
Replies
5
Views
683
Germermaman
Germermaman
DesEngineer4
  • Locked
  • Question Question
Autovue_Drawing Compare
Replies
6
Views
296
3DDave
3DDave
PratikG
  • Locked
  • Question Question
Contradicting drawing callouts
Replies
3
Views
394
3DDave
3DDave
umatrix
  • Locked
  • Question Question
Perpendicularty to common datums
Replies
13
Views
907
Woosang
Woosang
rfkflf
  • Locked
  • Question Question
Is the profile tolerance on my cone fully defined?
Replies
7
Views
762
Burunduk
Burunduk
Inund8_ca
  • Locked
  • Question Question
GD&T for Threaded holes
2
Replies
26
Views
5K
Burunduk
Burunduk
sendithard
  • Locked
  • Question Question
Composite Profile question
Replies
1
Views
436
Burunduk
Burunduk
rollingcloud
  • Locked
  • Question Question
This cannot be correct
Replies
3
Views
362
3DDave
3DDave
SeasonLee
  • Locked
  • Question Question
Will straightness affect the circularity and cylindricity?
2
Replies
36
Views
2K
greenimi
greenimi
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top