Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Drafting Standards, GD&T & Tolerance Analysis

sendithard
  • Locked
  • Question Question
Square size callout position
Replies
3
Views
958
Wuzhee
Wuzhee
Vladdo
  • Locked
  • Question Question
Using dimension with plus minus tolerance at intersection of basic dimension.
Replies
6
Views
576
Vladdo
Vladdo
CTengIS
  • Locked
  • Question Question
Profile Of a Line application
Replies
9
Views
677
CTengIS
CTengIS
Garrett Green
  • Locked
  • Question Question
Chamfer Callout on Through Hole in Tube
Replies
5
Views
757
SDETERS
SDETERS
CTengIS
  • Locked
  • Question Question
Deciding on cutoff length values for roughness or waviness to state on the drawing
Replies
12
Views
2K
CTengIS
CTengIS
RevSol
  • Locked
  • Question Question
Common Datum with eccentric axis' to control orientation of flats. GD&T
Replies
7
Views
1K
Burunduk
Burunduk
sendithard
  • Locked
  • Question Question
Is this a pattern rule or simultaneous rule
2
Replies
23
Views
1K
pmarc
pmarc
TylerD
  • Locked
  • Question Question
Surface Finish Before/After Heat treat
Replies
4
Views
552
TylerD
TylerD
JLS357
  • Locked
  • Question Question
GD&T tangent modifier with profile tolerance?
Replies
7
Views
780
jassco
jassco
Verkstad
  • Locked
  • Question Question
Envelope iso linear dimension
Replies
5
Views
483
pmarc
pmarc
YNIEH
  • Locked
  • Question Question
Position Tolerance, Basic Dimension, and Aligned Features
Replies
5
Views
865
YNIEH
YNIEH
KMHC
  • Locked
  • Question Question
Composite tolerance question
Replies
5
Views
654
DanStro
DanStro
Diametrix
  • Locked
  • Question Question
Can you skip a projected view on a drawing?
2 3
Replies
40
Views
2K
ctopher
ctopher
supergee
  • Locked
  • Question Question
Should one be able to do a tolerance stackup from a GOOD assembly drawing
Replies
10
Views
793
drawoh
drawoh
JGarcas
  • Locked
  • Question Question
Does anyone has or know where to find the solution to FIG.4-7 drawing from ASME-Y14.5M-2009.
2
Replies
30
Views
1K
3DDave
3DDave
kokerkov
  • Locked
  • Question Question
angular tolerance in ISO 2768-1 for sheet metal process
Replies
5
Views
1K
kokerkov
kokerkov
DJ Nelson
  • Locked
  • Question Question
total run out on a datum
2
Replies
24
Views
2K
3DDave
3DDave
Enrico Urru
  • Locked
  • Question Question
Thickness GD&T
Replies
11
Views
1K
Enrico Urru
Enrico Urru
metrologic
  • Locked
  • Question Question
Y14.45 Measuremnt Data Reporting questions
Replies
8
Views
1K
axym
axym
Andera
  • Locked
  • Question Question
ASME Y14.43 and AIAG Gauge R&R rules
Replies
2
Views
683
metrologic
metrologic
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top