Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

QC, Inspection & Testing engineering

Gokul Vijay
  • Locked
  • Question Question
As per B31.3 Impact test acceptance
Replies
3
Views
403
SJones
SJones
Ben22
  • Locked
  • Question Question
Books on Piping/construction management
Replies
0
Views
159
Ben22
Ben22
MKA4281
  • Locked
  • Question Question
Recalibration of Safety Relief Valves
Replies
1
Views
174
LittleInch
LittleInch
ird192
  • Locked
  • Question Question
IQI selection
Replies
3
Views
486
david339933
david339933
OZWelder
  • Locked
  • Question Question
P number ground for cladded material
Replies
2
Views
244
-
?
65CCJ
  • Locked
  • Question Question
Thread Form isn't correct but gages OK for 1"NPT Male Thread - Is the picture grounds for scrap
Replies
8
Views
714
65CCJ
65CCJ
Gokul Vijay
  • Locked
  • Question Question
PWHT maximum soaking time?
Replies
7
Views
995
r6155
r6155
Gambler52
  • Locked
  • Question Question
I am new to GD&T can someone please explain what all of these mean? Thank you so much
Replies
6
Views
2K
Tmoose
Tmoose
Karik87
  • Locked
  • Question Question
What is Roll number and Item number?
Replies
4
Views
649
Karik87
Karik87
ird192
  • Locked
  • Question Question
Mil-STD-3040 procedures and welder qualification
Replies
2
Views
576
gtaw
gtaw
Nashanas
  • Locked
  • Question Question
ASQ CQA
Replies
0
Views
156
Nashanas
Nashanas
HJackson
  • Locked
  • Question Question
GD&T - Profile
Replies
2
Views
284
ewh
ewh
Merc-
  • Locked
  • Question Question
What are certifications required to
Replies
3
Views
369
r6155
r6155
Merc-
  • Locked
  • Question Question
Pressure test for open end piping network
Replies
2
Views
584
LittleInch
LittleInch
Nashanas
  • Locked
  • Question Question
Quality Audit for renewal ISO 9001
Replies
14
Views
590
IRstuff
IRstuff
OZWelder
  • Locked
  • Question Question
Heat and cooling rate. ASME I and or ASME B31.1
Replies
9
Views
1K
OZWelder
OZWelder
Beginner - Inspector
  • Locked
  • Question Question
EEMUA 234 90/10 CU NI ASTM 466 UNS 70610 Vs UNS 7060X
Replies
0
Views
278
Beginner - Inspector
Beginner - Inspector
AliGrailly
  • Locked
  • Helpful tip Helpful tip
Length of pipe to be used in PQR
Replies
4
Views
666
M.CH
M.CH
OZWelder
  • Locked
  • Question Question
Hello, I am trying to work out w
Replies
3
Views
347
r6155
r6155
AliGrailly
  • Locked
  • Question Question
NDE for small diameter on first production
Replies
5
Views
279
DekDee
DekDee
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top