Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Plastics Engineering general discussion

waynethepain
  • Locked
  • Question Question
Injected EVA foam density.
Replies
9
Views
255
patprimmer
patprimmer
hydrive
  • Locked
  • Question Question
refurbishing plastic (polycarbonate) and preventing scratches
Replies
9
Views
521
hydrive
hydrive
jerzy
  • Locked
  • Question Question
Preloading support pillars.
Replies
12
Views
648
jerzy
jerzy
lobos8403
  • Locked
  • Question Question
Round into Hex Interferance fit.
Replies
1
Views
668
loughnane
loughnane
loughnane
  • Locked
  • Question Question
amorphous or semi-crystalline polymers for creep resistance?
Replies
7
Views
532
Demon3
Demon3
canthony1
  • Locked
  • Question Question
PC vs ABS Tool Wear
Replies
2
Views
268
canthony1
canthony1
klank
  • Locked
  • Question Question
warp problem in Autodesk Moldflow adviser.
Replies
3
Views
207
btrueblood
btrueblood
dans67
  • Locked
  • Question Question
Thin wall HDPE extrusion
Replies
10
Views
543
patprimmer
patprimmer
mgnt8
  • Locked
  • Question Question
Neck finish specifications
Replies
1
Views
105
RyanVLee
RyanVLee
sizzer33
  • Locked
  • Question Question
PMMA cube manufacturing
Replies
7
Views
305
patprimmer
patprimmer
JasonNicholson
  • Locked
  • Question Question
Dimensioning and Tolerancing in Plastics: Where do get Training?
Replies
5
Views
527
patprimmer
patprimmer
reyemka
  • Locked
  • Question Question
Airtight interlock design
Replies
6
Views
256
cpretty
cpretty
xjcurtisx
  • Locked
  • Question Question
anyone know a material that meets this criteria? used on a labtop
Replies
2
Views
83
btrueblood
btrueblood
klank
  • Locked
  • Question Question
Moldflow vs. Moldex 3D??
Replies
5
Views
809
bobslo
bobslo
singerk
  • Locked
  • Question Question
Polycarbonate regrind properties
Replies
1
Views
154
patprimmer
patprimmer
petersi
  • Locked
  • Question Question
Cheap Mold for a 5mm width part
Replies
8
Views
208
raynjer
raynjer
jadhava
  • Locked
  • Question Question
Shrinkage of PPS rod when heated to 100 degC.
Replies
2
Views
143
Demon3
Demon3
jaubert
  • Locked
  • Question Question
What is the most flammable common plastic?
Replies
14
Views
772
Demon3
Demon3
prdave00
  • Locked
  • Question Question
Removing acrylic deposits from glassware
Replies
3
Views
88
prdave00
prdave00
NateUMF
  • Locked
  • Question Question
Nylon absorption and water loss over time causing it to become brittle
Replies
11
Views
2K
patprimmer
patprimmer
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top