Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Drafting Standards, GD&T & Tolerance Analysis

pmarc
  • Locked
  • Question Question
What is a difference between Center Point and Median Point?
Replies
3
Views
401
pmarc
pmarc
jj11142
  • Locked
  • Question Question
Chamfer call out
Replies
10
Views
2K
nithink
nithink
JJAV1983
  • Locked
  • Question Question
Male Plastic Polycarbonate M4 insert wont fit in an M4 hole made on an Aluminum plate.
2
Replies
20
Views
465
powerhound
powerhound
floide
  • Locked
  • Question Question
How to dimension trapezoid part?
Replies
14
Views
643
MechNorth
MechNorth
616Nickel
  • Locked
  • Question Question
How to persuade engineers to abandon silly tolerances?
2
Replies
28
Views
743
nobog
nobog
cjccmc
  • Locked
  • Question Question
Holes in line
Replies
2
Views
257
cjccmc
cjccmc
16valan
  • Locked
  • Question Question
Specifying a surface finish to a region of a face
Replies
4
Views
556
MechNorth
MechNorth
Madhu454
  • Locked
  • Question Question
Datum & DOF
Replies
6
Views
126
drawoh
drawoh
duk748
  • Locked
  • Question Question
flatness symbol on shaft diameter
Replies
8
Views
351
duk748
duk748
Rhyder88
  • Locked
  • Question Question
What dose the symbol "~" denotes in the drawing which is located at the top left corenr of
Replies
10
Views
857
Rhyder88
Rhyder88
KushWadhwani
  • Locked
  • Question Question
How to give dimesions in Assembly
Replies
1
Views
98
CheckerHater
CheckerHater
srikanthsatyam
  • Locked
  • Question Question
GD&T. Apply Flatness to the Planar Feature of Size
Replies
7
Views
233
Belanger
Belanger
fsincox
  • Locked
  • Question Question
Refining a profile tolerance with an inch/inch type spec?
Replies
15
Views
697
fsincox
fsincox
RXMetrology
  • Locked
  • Question Question
How to distribute general assembly profile tolerance to component parts
Replies
7
Views
173
RXMetrology
RXMetrology
Tunalover
  • Locked
  • Question Question
Flatness per unit length
Replies
5
Views
759
MechNorth
MechNorth
SeasonLee
  • Locked
  • Question Question
Flatness or Profile callout?
Replies
2
Views
115
MechNorth
MechNorth
leeekim
  • Locked
  • Question Question
Note: Machine as a pair
Replies
13
Views
508
MechNorth
MechNorth
SiW979
  • Locked
  • Question Question
Is this GD&T correct
2
Replies
27
Views
441
CheckerHater
CheckerHater
Valek
  • Locked
  • Question Question
3D Model Call Outs.
Replies
6
Views
251
weavedreamer
weavedreamer
geekman25
  • Locked
  • Question Question
Drawing which contains inch and metric dimensions
Replies
13
Views
2K
ctopher
ctopher
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top