Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Drafting Standards, GD&T & Tolerance Analysis

pmarc
  • Locked
  • Question Question
Tolerancing of cones
Replies
17
Views
965
pmarc
pmarc
bxbzq
  • Locked
  • Question Question
casting and machining on seperate drawing
Replies
17
Views
576
MechNorth
MechNorth
jjbiot
  • Locked
  • Question Question
pin & hole slip tolerance
Replies
7
Views
712
ak762
ak762
SDETERS
  • Locked
  • Question Question
Controlled radius Simliar or to on a diameter.
Replies
10
Views
312
SDETERS
SDETERS
bxbzq
  • Locked
  • Question Question
partially opposed FOS
2
Replies
21
Views
670
MechNorth
MechNorth
chavelo
  • Locked
  • Question Question
ISO title block
Replies
5
Views
1K
CheckerHater
CheckerHater
hengone
  • Locked
  • Question Question
How to inspect profile tolerance of an big assembly?
Replies
3
Views
182
MechNorth
MechNorth
bxbzq
  • Locked
  • Question Question
generatrix of cylinder surface as datum?
Replies
5
Views
213
MechNorth
MechNorth
roywu2002
  • Locked
  • Question Question
Can you use true position on planar feature of size?
Replies
5
Views
555
roywu2002
roywu2002
greenimi
  • Locked
  • Question Question
Runout with MMC/MMB on DRF? No. Profile with MMC/MMB on DRF? Yes
Replies
9
Views
323
CheckerHater
CheckerHater
KevinNM
  • Locked
  • Question Question
Grouping "Separate Requirements"
Replies
4
Views
293
MechNorth
MechNorth
KevinNM
  • Locked
  • Question Question
Mechanical Envelopes Min/Max dims vs Profile
Replies
2
Views
194
MechNorth
MechNorth
Madhu454
  • Locked
  • Question Question
Restaining : Secondary Datum Feature
Replies
1
Views
95
MechNorth
MechNorth
bxbzq
  • Locked
  • Question Question
where to place profile tolerance fcf for angled hole
Replies
6
Views
109
CheckerHater
CheckerHater
Madhu454
  • Locked
  • Question Question
Does secondary datum feature-B required?
Replies
8
Views
258
greenimi
greenimi
SeasonLee
  • Locked
  • Question Question
DRF of casting and machined part
Replies
7
Views
103
SeasonLee
SeasonLee
bxbzq
  • Locked
  • Question Question
TOLERANCING AN ANGULAR SURFACE WITH A BASIC ANGLE
Replies
2
Views
78
Belanger
Belanger
SMOKES
  • Locked
  • Question Question
316L g6/h7 fit
Replies
3
Views
189
Walterke
Walterke
psiwak
  • Locked
  • Question Question
Watch Where You Put That Triangle - Discusion
2
Replies
35
Views
991
Belanger
Belanger
SMOKES
  • Locked
  • Question Question
g6 fit and 316L
Replies
1
Views
237
juergenwt
juergenwt
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top