Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Boiler and Pressure Vessel engineering

AskTooMuch
  • Locked
  • Question Question
pv elite clip design
Replies
1
Views
182
r6155
r6155
david339933
  • Locked
  • Question Question
Backing Strips below -20F
Replies
10
Views
470
david339933
david339933
EngineerRed
  • Locked
  • Question Question
Allowable stress Vs Yield strength for bolting design
Replies
8
Views
1K
r6155
r6155
CobusvanJ
  • Locked
  • Question Question
How to calculate required wall thickness for square duct
Replies
7
Views
987
HTURKAK
HTURKAK
ReliaEng2008
  • Locked
  • Question Question
Torque Values for Pressure Vessel Body Flanges
Replies
5
Views
2K
SnTMan
SnTMan
Ramdeom
  • Locked
  • Question Question
HVAC Plant Sizing
Replies
1
Views
128
SnTMan
SnTMan
Engineer_M
  • Locked
  • Question Question
Relief Valve on LN2 pressure vessel
Replies
0
Views
148
Engineer_M
Engineer_M
Doodler3D
  • Locked
  • Question Question
Standard vs Nonstandard Vessels
Replies
9
Views
665
Doodler3D
Doodler3D
aaloui
  • Locked
  • Question Question
Gasket load at operating condition ASME VIII-1 Appendix 2
Replies
6
Views
630
aaloui
aaloui
DK44
  • Locked
  • Question Question
Are Nozzle loads considered in Shell & Tube Heat Exchanger Saddle support design
Replies
8
Views
506
DK44
DK44
AlbeBersani
  • Locked
  • Question Question
ASME B31.8 - PWHT on WEAR Pad for Saddles
Replies
8
Views
560
AlbeBersani
AlbeBersani
Sam Martin
  • Locked
  • Question Question
Non-condensing, close looped, water tube boiler material and ASME code suggestion
Replies
0
Views
87
Sam Martin
Sam Martin
DK44
  • Locked
  • Question Question
Round Condensers
Replies
4
Views
249
MJCronin
MJCronin
Newport2
  • Locked
  • Question Question
EN 13445-3 - 10.5.2
Replies
3
Views
522
Newport2
Newport2
Flash8111
  • Locked
  • Question Question
Nozzle loads
Replies
2
Views
138
Strook
Strook
oghenhope
  • Locked
  • Question Question
What is the best Pressure Vessel Software Program for the Design of Sphere Tank: ASME SECTION VIII,
Replies
1
Views
147
SnTMan
SnTMan
Matrix_93
  • Locked
  • Question Question
Nozzle Pro Loads on nozzle shell junction
Replies
0
Views
212
Matrix_93
Matrix_93
ALangley
  • Locked
  • Question Question
SA-479-317L isn't in ASME BPVC.II.D 2019?
Replies
4
Views
254
r6155
r6155
az5333
  • Locked
  • Question Question
FEA Postprocessing of a Flat Head with Internal Ribs - ASME BPCV Sec VIII Div 2 Part 5
Replies
16
Views
627
sameer21101970
sameer21101970
Ken_C
  • Locked
  • Question Question
Pressure Vessel re-rating with discontinued material
Replies
2
Views
292
Ken_C
Ken_C
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top