Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

Register Log in
  • Congratulations waross on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Boiler and Pressure Vessel engineering

DK44
  • Locked
  • Question
Are Nozzle loads considered in Shell & Tube Heat Exchanger Saddle support design
Replies
8
Views
389
DK44
DK44
AlbeBersani
  • Locked
  • Question
ASME B31.8 - PWHT on WEAR Pad for Saddles
Replies
8
Views
415
AlbeBersani
AlbeBersani
Sam Martin
  • Locked
  • Question
Non-condensing, close looped, water tube boiler material and ASME code suggestion
Replies
0
Views
67
Sam Martin
Sam Martin
DK44
  • Locked
  • Question
Round Condensers
Replies
4
Views
183
MJCronin
MJCronin
Newport2
  • Locked
  • Question
EN 13445-3 - 10.5.2
Replies
3
Views
380
Newport2
Newport2
Flash8111
  • Locked
  • Question
Nozzle loads
Replies
2
Views
86
Strook
Strook
oghenhope
  • Locked
  • Question
What is the best Pressure Vessel Software Program for the Design of Sphere Tank: ASME SECTION VIII,
Replies
1
Views
124
SnTMan
SnTMan
Matrix_93
  • Locked
  • Question
Nozzle Pro Loads on nozzle shell junction
Replies
0
Views
162
Matrix_93
Matrix_93
ALangley
  • Locked
  • Question
SA-479-317L isn't in ASME BPVC.II.D 2019?
Replies
4
Views
180
r6155
r6155
az5333
  • Locked
  • Question
FEA Postprocessing of a Flat Head with Internal Ribs - ASME BPCV Sec VIII Div 2 Part 5 1
Replies
16
Views
461
sameer21101970
sameer21101970
Ken_C
  • Locked
  • Question
Pressure Vessel re-rating with discontinued material
Replies
2
Views
128
Ken_C
Ken_C
OscarAb
  • Locked
  • Question
Two Bolt Flanges
Replies
3
Views
543
JStephen
JStephen
Raza Rauf
  • Locked
  • Question
Heat Exchanger Re-tubing
Replies
7
Views
202
Christine74
Christine74
aaloui
  • Locked
  • Question
Clamp Connections ASME VIII-1 Appendix 24
Replies
2
Views
308
aaloui
aaloui
inammanj123
  • Locked
  • Question
compressive stress error due to high temperature( more than 900 deg.F)
Replies
2
Views
231
Morcuse
Morcuse
Ehiman1
  • Locked
  • Question
External loads on standard flange
Replies
2
Views
84
Strook
Strook
AlbertaMecchie
  • Locked
  • Question
Calculating Steam flow through and open ended vent pipe
Replies
4
Views
655
LittleInch
LittleInch
td_eng
  • Locked
  • Question
ASME VIII DIV 2 - PART 5 DBA 1
Replies
7
Views
336
BJI
BJI
AlexanderChacin
  • Locked
  • Question
Pressure Vessel Saddle
Replies
6
Views
191
r6155
r6155
flakyman
  • Locked
  • Question
Fitness for service software
Replies
3
Views
543
georgeverghese
georgeverghese
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top Bottom