dear all,
with reference to ASME B31.3 Table 304.1.1 Values of Coefficient Y Low Alloy Material Like A335-P11 or A691 1.25Cr or A234-WP11 which is the group to take as reference for thickness calculation ? "Ferritic Steel" or "Other ductile metals" ?
thank for your supports
regards
dear all,
with reference to ASME B31.3 Table 304.1.1 Values of Coefficient Y Low Alloy Material Like A335-P11 or A691 1.25Cr or A234-WP11 which is the group to take as reference for thickness calculation ? "Ferritic Steel" or "Other ductile metals" ?
thank for your supports
regards
I'm looking for info regarding thickness calculation to be applied in Algeria cuntry. Are There additional requirents to asme B 31.3 ? Thanks in advance for help me
Referring to para 304.3.3 of B31.3, is the calculation formula applicable to 'Set In' configuration (branch insterted in the cutted Run Pipe) or to 'Set On' configuration (branch put on the cutted Run Pipe)...
Dear all,
our client is asking us to specify LTCS material impact tested at -52°C. Anybody have any experience about values of impact tests at this Temperature for cast (A352-LCB/LCC) and forged (A182-LF2) grades?
Thank you in advance
hello thanks for your reply ..
as per ASME B 31.4, allowable stress considered for thickness calculation are 0.72 x yield stress.
my basic doubt is whether vacuum thickness calculation applicable for ASME B 31.4, if yes then what will the ASME code to be followed.
ASME B 31.3 states ASME Sec...
Hi,
I have referred ASME B 31.4 edition 2012, where it is not clearly mentioned about the code or procedure to be followed for straight pipe under external condition .
whereas in ASME B 31.3, stated according to ASME sec VIII UG28.
my queries are.
1. how to verify the pipe thickness for full...
Dear All ,
In ASME B 31.3 -2012 edition, we found that allowable stress for B705 material is availble in TABLE A-1, but for B474-UNS08825 not available.
In this concern, as we have calculated the Thickness of pipe based on the allowable stress for B705. can we accept the deviation of B474 pipe...
Hi all
we have recieved from our process dept a request to specify non slam high integrity design check valves.
Could you help us to understand the meaning of "High Integrity" ?
thank for your helps
regards
metma
Thank you for your reply, I confirm that the correct paragraph is 9.4.3.
I have already asked and interpretation to ASME, and they reply to me that they will take care of the question during next commitee meeting (next month).
Once I will have the reply, I will post it.
Regards
Metma
I have purchased some big stainless steel reducers designed according to ASME B16.9.
In order to qualify the desing, I have asked to the manufacturer the proof testing, but I got a certificate relevant to a carbon steel reducer.
So my question is: can a proof test certificate relevant to a...
Good afternoon.
In the coal power plant I am taking care, there is a cast valve made of TSM 1424 Gr B: could you please suggest me what kind of material is that? do you have any datasheet?
The only thing I know is that it is a Cr-Mo-V steel, anything else.
Thank you very much for your help...
You could use:
-HDPE gathering line: HDPE adaptor (stub end) and cs ANSI free flange (lap joint);
-cs header: CS regular ANSI flange.
In this way nuts work on two cs flanges instead of a HDPE flange and a cs flange; for this reason facing of the mating cs flange (header side) can be both RF and...
I have collected some info.
The 20 deg lateral in subject (I attach a sketch) is used to collect polymer powder from different reactors and to carry it, through a vertical pipe, to a below reactor; the slope of 20 deg (from a vertical axis) is required in order to prevent powder from settling on...
Dear pbrown,
last month we had the same matter for a cryogenic line in a LNG plant, for which we considered whether to use a high Ni alloy or a SS304.
In particular we have taken 9%Ni (ASTM A353 and A553) and 36%Ni (Alloy 36) into consideration:
-pipes are available for both materials (at...
Thank you all for your answers: on Monday, from the office, I will post a sketch and some details to share with you this matter.
Unfortunately I confirm you that there is no possibility of a joint redesign.
Regards