7050 Aluminum Alloy Microstructure

• May 13, 2025

• #2

mfgenggear

Aerospace

Jan 23, 2008

3,602

US

OP
There should be examples in the ASM heat treating hand book. Don't remember the upto date volume.

 

Upvote 0 Downvote

• May 13, 2025

• #3

mfgenggear

Aerospace

Jan 23, 2008

3,602

US

OP
Also AMS material specification for this material for castings and wrought material.

 

Upvote 0 Downvote

• May 13, 2025

• Thread starter
• #4

SMF1964

Materials

Aug 5, 2003

306

US

Thanks for the suggestions. My copies (the Red volumes) don't have microstructures in the HT volume (Vol 4) and the metallography & microstructures only have 3 images, from plate. I'll dig around for the AMS spec literature.

 

Upvote 0 Downvote

• May 13, 2025

• #5

EdStainless

Materials

May 20, 2004

16,346

Waukesha WI USA

the current ASM handbook is two volumes newer than yours.
There also is an ASM specialty handbook on Al alloys that might help.

 

Upvote 0 Downvote

• May 20, 2025

• #6

WKTaylor

Well-known member

Sep 24, 2001

4,276

US

What was the material spec for the forged billet [block, etc]? What were the finished dimensions for the billet?

Was the forged billet HT processed to the -O1... or directly to the -T7452?

Did the billet have material certifications from the processor? IE...

What was the forging spec? Was billet grain size/control/flow checked? Chemistry/hardness/conductivity/tensile Checks?

Was a thru-ultra sonic required... in multiple orientations... and to what class was the block rated? Typical ASTM B594

Was this the billet a one-of-a-kind... or was-it-one of many in a lot 'heat'?

Has the impeller been 'in-service'?

/NOTE/ 7050 is a well-studied alloy with there are many technical papers many ... but know basic info on the raw-stock is a big starter.

I design lots of replacement parts from 7050 forged block and plate... raw stock certifications are the starting point.

If find the concept of an aluminum 'impeller'... with high rotation speed and fluid thrust... and likely vibrations and/or cavitation... a bit unnerving.

My head hurts... thinking too hard about this...

 

Upvote 0 Downvote

• May 28, 2025

• #7

Dhurjati Sen

Materials

Dec 14, 2017

1,001

IN

Good to see that ASM Handbooks still rule.

 

Upvote 0 Downvote

• May 28, 2025

• #8

WKTaylor

Well-known member

Sep 24, 2001

4,276

US

ASM Handbook Volume 9: Metallography and Microstructures

ASM Handbook Volume 9: Metallography and Microstructures - ASM International

Volume 9 is recommended for anyone who specifies, performs, monitors, evaluates, or uses metallurgical analysis for production QC, research, or educational training. Important updates reflecting the substantial changes in automation, equipment, consumable products and preparation methodology, as...

www.asminternational.org

ASM Specialty Handbook: Aluminum and Aluminum Alloys

ASM Specialty Handbook: Aluminum and Aluminum Alloys - ASM International

This one-stop reference is a tremendous value and time saver for engineers, designers and researchers who select and process aluminum and aluminum alloys. Covers all aspects of the selection, processing, properties, and performance of aluminum.

www.asminternational.org

 

Upvote 0 Downvote