Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Drafting Standards, GD&T & Tolerance Analysis

Vah1D
  • Locked
  • Question Question
Flatness on both sides + Parallelism vs. Flatness on one side + Parallelism
Replies
1
Views
644
Burunduk
Burunduk
Finglas
  • Locked
  • Question Question
General Tolerances Unless Otherwise Stated (Linear/angular)
Replies
15
Views
5K
Burunduk
Burunduk
sharky98
  • Locked
  • Question Question
Total runout or position + perpendicularity + cylindricity
Replies
5
Views
536
Tmoose
Tmoose
ASHWA
  • Locked
  • Question Question
MMC principle used in Profile Controls.
Replies
2
Views
253
ASHWA
ASHWA
Martin T
  • Locked
  • Question Question
GD&T online courses BS:8888 & ISO
Replies
3
Views
265
3DDave
3DDave
Stephen Robertson
  • Locked
  • Question Question
Compound datums for hole intentionally not perpendicular to surface into which it is drilled
Replies
5
Views
439
aniiben
aniiben
Al James at General Atomics
  • Locked
  • Question Question
3D Variational Analysis Software CETOL-6sigma versus 3DCS
Replies
8
Views
628
Burunduk
Burunduk
Burunduk
  • Locked
  • Question Question
Virtual condition of threaded holes (modified MMC)
Replies
5
Views
788
Burunduk
Burunduk
Dean Watts
  • Locked
  • Question Question
ASME Y14.45 Public Review and Comment Period - July 24th to September 20th, 2020
2
Replies
29
Views
715
SeasonLee
SeasonLee
Andera
  • Locked
  • Question Question
ISO question (CZ and UZ)
Replies
0
Views
400
Andera
Andera
Sa-Ro
  • Locked
  • Question Question
Zero setting on datum
Replies
7
Views
287
Burunduk
Burunduk
herkyengineer
  • Locked
  • Question Question
Unique GD&T Layout Question
Replies
8
Views
244
jassco
jassco
Sa-Ro
  • Locked
  • Question Question
Perpendicularity
Replies
4
Views
172
Sa-Ro
Sa-Ro
flash3780
  • Locked
  • Question Question
What's the correct term to apply a control to a volumetric region of material?
Replies
4
Views
237
Burunduk
Burunduk
J-C
  • Locked
  • Question Question
ANSI vs ISO - Alignment
Replies
2
Views
2K
dgallup
dgallup
Woosang
  • Locked
  • Question Question
Orientation constrain in the lower segment of composite position tolerance.
Replies
12
Views
288
Burunduk
Burunduk
ASHWA
  • Locked
  • Question Question
Why we need 2 Callout's for a FOS?
2
Replies
38
Views
1K
ASHWA
ASHWA
ASHWA
  • Locked
  • Question Question
Doubt in Cylindricity
Replies
12
Views
546
ASHWA
ASHWA
Stick369
  • Locked
  • Question Question
Tangent edge transition standard
2
Replies
20
Views
1K
powerhound
powerhound
aniiben
  • Locked
  • Question Question
Movable datum target on flexible parts
Replies
1
Views
158
drawoh
drawoh
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top