Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Drafting Standards, GD&T & Tolerance Analysis

KENAT
  • Locked
  • Question Question
Implied Centerlines/Symmetry
2 3
Replies
46
Views
2K
DesignBiz
DesignBiz
ja500
  • Locked
  • Question Question
MMC on datums
Replies
6
Views
227
MechNorth
MechNorth
kimocal
  • Locked
  • Question Question
Basic Dimension, positional feature with MMC. Legal?
Replies
10
Views
360
MechNorth
MechNorth
ticker
  • Locked
  • Question Question
runout
Replies
6
Views
149
MechNorth
MechNorth
jcastaneda79
  • Locked
  • Question Question
Can a profile tolerance used to control a true position?
Replies
18
Views
1K
MechNorth
MechNorth
PeterStock
  • Locked
  • Question Question
Tolerance of Implied 90 Degree Angle
Replies
9
Views
954
MechNorth
MechNorth
joebk
  • Locked
  • Question Question
tolerance block angle vs. length vs. Rule 1
Replies
17
Views
500
KENAT
KENAT
Waidesworld
  • Locked
  • Question Question
Call out symbol question
Replies
13
Views
527
PeterStock
PeterStock
SDETERS
  • Locked
  • Question Question
ASME Y14.5M 2009?
2
Replies
24
Views
865
ewh
ewh
JasonSp
  • Locked
  • Question Question
2 Single Segment FCF to make Rectangular Tolerance Zone?
2 3
Replies
53
Views
813
axym
axym
KENAT
  • Locked
  • Question Question
Current state of Model Based Definition
2 3
Replies
43
Views
862
KENAT
KENAT
fcsuper
  • Locked
  • Question Question
Pos Tol applied to pattern (how to?)
2 3 4
Replies
78
Views
1K
btrueblood
btrueblood
SeasonLee
  • Locked
  • Question Question
Lever DRF callout
Replies
4
Views
259
SeasonLee
SeasonLee
Kennycrft
  • Locked
  • Question Question
Datum shift?
Replies
6
Views
933
dingy2
dingy2
SolidWorksGuru
  • Locked
  • Question Question
Tolerance Block "Crossout" - Per what std?
2
Replies
33
Views
796
KENAT
KENAT
swertel
  • Locked
  • Question Question
MMC on Datums for Runout
2
Replies
26
Views
679
MechNorth
MechNorth
DesignBiz
  • Locked
  • Question Question
Tolerance of Positoin - feature positioned to itself ???
2 3 4
Replies
65
Views
1K
DesignBiz
DesignBiz
JohnJ52
  • Locked
  • Question Question
Weldment GD&T Guidance
Replies
8
Views
1K
JohnJ52
JohnJ52
mechman67
  • Locked
  • Question Question
Proper Masking Notes
Replies
3
Views
1K
ctopher
ctopher
SeasonLee
  • Locked
  • Question Question
Datum setup
2 3
Replies
50
Views
1K
PaulJackson
PaulJackson
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top