Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Drafting Standards, GD&T & Tolerance Analysis

Madhu454
  • Locked
  • Question Question
Considerations for Manufacturabality.
Replies
12
Views
175
CheckerHater
CheckerHater
SeasonLee
  • Locked
  • Question Question
Designer's intent to control position, concentricity or ..
Replies
9
Views
89
SeasonLee
SeasonLee
bucknast
  • Locked
  • Question Question
Measuring Runout of Two Internal Features
Replies
1
Views
415
powerhound
powerhound
Jieve
  • Locked
  • Question Question
Is this datum hole callout correct? - ISO
Replies
9
Views
482
pmarc
pmarc
Jieve
  • Locked
  • Question Question
Profile Tolerance for Slots
Replies
7
Views
614
SeasonLee
SeasonLee
Ksplice
  • Locked
  • Question Question
true position of a rectangular feature
Replies
7
Views
546
Belanger
Belanger
powerhound
  • Locked
  • Question Question
Projected tangent plane -- What do you think?
Replies
5
Views
180
powerhound
powerhound
Reman101
  • Locked
  • Question Question
Concentricity v/s coaxiality (yet again) on a CMM
Replies
5
Views
362
CheckerHater
CheckerHater
Jieve
  • Locked
  • Question Question
ISO Drawing Questions - Views & Hole Callouts
Replies
6
Views
666
CheckerHater
CheckerHater
gcubed888
  • Locked
  • Question Question
Standard (Or Generally Agreed) Method For Measuring Run-out
Replies
16
Views
1K
ptruitt
ptruitt
rkmistry
  • Locked
  • Question Question
Flatness tolerance callout I have never come across
Replies
8
Views
222
rkmistry
rkmistry
Jieve
  • Locked
  • Question Question
Measurement of a part with position control refinement
Replies
5
Views
155
Jieve
Jieve
fcsuper
  • Locked
  • Question Question
Does the ISO drafting standards actually say not to use trailing (insignificant) zeros on dimensions
2
Replies
23
Views
1K
CheckerHater
CheckerHater
bxbzq
  • Locked
  • Question Question
datum setup of irregular holes on a flange
Replies
3
Views
105
bxbzq
bxbzq
Odiemena
  • Locked
  • Question Question
Profile tolerance vs linear tolerance - (GD&T newbie)
Replies
11
Views
693
CheckerHater
CheckerHater
rnanj001
  • Locked
  • Question Question
Critical Dimension
2 3
Replies
42
Views
5K
fcsuper
fcsuper
rcskswc
  • Locked
  • Question Question
"NA" THREAD CALLOUT
Replies
4
Views
430
CheckerHater
CheckerHater
jefrojo
  • Locked
  • Question Question
Calculation of position tolerance with reference to hole
2
Replies
27
Views
1K
Belanger
Belanger
arandy
  • Locked
  • Question Question
Hi Eng-Tip community. I am a young
Replies
13
Views
290
pmarc
pmarc
RonnyC
  • Locked
  • Question Question
datumshift: MMC size limit or virtualcondition
Replies
6
Views
178
RonnyC
RonnyC
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top