Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Drafting Standards, GD&T & Tolerance Analysis

UGMENTALCASE
  • Locked
  • Question Question
GD & T Help needed please!
Replies
3
Views
140
drawoh
drawoh
idgara73612
  • Locked
  • Question Question
Drawing Material Specs - Initial vs Final Condition
Replies
13
Views
730
drawoh
drawoh
MechNorth
  • Locked
  • News News
Passing of a friend and member of this Forum
Replies
9
Views
557
MechNorth
MechNorth
meanderngineer
  • Locked
  • Question Question
Aesthetic Surface Finish Callout (Black Delrin)
Replies
8
Views
539
ctopher
ctopher
Oaklandishh
  • Locked
  • Question Question
Flatness on a per unit basis
Replies
2
Views
414
CheckerHater
CheckerHater
jdmmech
  • Locked
  • Question Question
Position Tolerance of a square feature on a disk
2
Replies
24
Views
2K
pylfrm
pylfrm
atle89
  • Locked
  • Question Question
Position mmc and datums mmc
Replies
0
Views
62
atle89
atle89
RealSaladsamurai
  • Locked
  • Question Question
Determining Allowable Positional Tolerances for a Dowel Pin/Slot
Replies
4
Views
1K
RealSaladsamurai
RealSaladsamurai
Belanger
  • Locked
  • Question Question
Must profile be applied to a basic profile?
2 3
Replies
43
Views
2K
drawoh
drawoh
Oaklandishh
  • Locked
  • Question Question
Is depth of press fit ever assumed on a drawing?
Replies
4
Views
739
CheckerHater
CheckerHater
ZachP
  • Locked
  • Question Question
Handy Features to Have on Drawing Templates
Replies
17
Views
462
Tunalover
Tunalover
bxbzq
  • Locked
  • Question Question
go nogo gages for precision machining features
Replies
3
Views
174
drawoh
drawoh
bear9298
  • Locked
  • Question Question
How to dimension compound curves and compound angles to those curvese GD&T
Replies
5
Views
345
bear9298
bear9298
greenimi
  • Locked
  • Question Question
Rule #1 and form thread
Replies
15
Views
359
CheckerHater
CheckerHater
RLD89
  • Locked
  • Question Question
Target points on edges
Replies
3
Views
299
drawoh
drawoh
ivanovi
  • Locked
  • Question Question
Datums in a drawing with thread
Replies
5
Views
316
dgallup
dgallup
marshell
  • Locked
  • Question Question
Combining Composite and Bidirectional call outs
Replies
19
Views
566
pmarc
pmarc
brandnew1
  • Locked
  • Question Question
Question regarding starting point to measure based off BASIC dimensions
Replies
9
Views
315
Gilmiril
Gilmiril
TolQ
  • Locked
  • Question Question
Profile tolerance w/ reference datums dimensioned from non-datum edges?
Replies
9
Views
273
JNieman
JNieman
RLD89
  • Locked
  • Question Question
Multi Single Segment Profiles in 1994
Replies
5
Views
278
pmarc
pmarc
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top