Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Boiler and Pressure Vessel engineering

Ali Haidar
  • Locked
  • Question Question
Nodes in PV Elite
Replies
2
Views
425
gr2vessels
gr2vessels
FPPE
  • Locked
  • Question Question
Ideal flange/gasket configuration for hydrogen service
Replies
12
Views
1K
FPPE
FPPE
Sajjad2164
  • Locked
  • Question Question
Indirect fired heater - Mass flow rate of fuel
Replies
18
Views
1K
Sajjad2164
Sajjad2164
Clement-Corri
  • Locked
  • Question Question
Yield Strength in ASTM Norms
Replies
4
Views
669
Clement-Corri
Clement-Corri
CSunny
  • Locked
  • Question Question
Validation of FEA results
Replies
2
Views
260
TGS4
TGS4
BZ29
  • Locked
  • Question Question
How to Support very long Pressure Vessel (Bullets) on two saddles?
2
Replies
35
Views
2K
MJCronin
MJCronin
cknsr123
  • Locked
  • Question Question
ASME - oval manhole
Replies
8
Views
775
davefitz
davefitz
Jimjoe
  • Locked
  • Question Question
Man way of pressure vessel relation to girth flange
Replies
2
Views
313
Jimjoe
Jimjoe
Karthik P
  • Locked
  • Question Question
Non-Standard/Customised Flange MAWP
Replies
3
Views
270
LittleInch
LittleInch
sarawana
  • Locked
  • Question Question
cathodic protection by using pressure vessel
Replies
1
Views
132
Dhurjati Sen
Dhurjati Sen
Mech_Guy_98
  • Locked
  • Question Question
Two adjacent opening compensation while overlapping
Replies
0
Views
137
Mech_Guy_98
Mech_Guy_98
steris
  • Locked
  • Question Question
Repair of Grinding Gouge
Replies
13
Views
873
DVWE
DVWE
Santosh Ingale
  • Locked
  • Question Question
Hello Experts, Does any one know a
Replies
8
Views
352
Resegone
Resegone
fabiobs
  • Locked
  • Question Question
Forged brass valves
Replies
5
Views
305
bcd
bcd
Mech_Guy_98
  • Locked
  • Question Question
ASME MATERIAL NOMENCLATURE
Replies
3
Views
283
Mech_Guy_98
Mech_Guy_98
inammanj123
  • Locked
  • Question Question
Why for SA 387 GR 11, Pvelite is making PWHT mandatory, even thickness less than 16 mm ?
Replies
3
Views
266
r6155
r6155
Saver2008
  • Locked
  • Question Question
CAPACITY OF A PRESSURE RELIEF VALVE FOR A STEAM DRUM
Replies
6
Views
1K
IM383
IM383
mjpetrag
  • Locked
  • Question Question
Brittle CS boiler tubes - hydrotesting
Replies
4
Views
266
mjpetrag
mjpetrag
FPPE
  • Locked
  • Question Question
MDMT Exemption at -45 °C for pressure components and welding specifications UCS-66/67/68
Replies
3
Views
373
FPPE
FPPE
FPPE
  • Locked
  • Question Question
ASME VIII-1 MDMT exemption for SB 163 N08825
Replies
4
Views
471
FPPE
FPPE
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top