Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations JStephen on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Boiler and Pressure Vessel engineering

cespi82
  • Locked
  • Question Question
MAWP vs DP for calculating minimum required thickness
Replies
7
Views
655
r6155
r6155
Rakesh2560
  • Locked
  • Question Question
support plate attachment to scrubber shell
Replies
1
Views
130
Dhurjati Sen
Dhurjati Sen
KernOily
  • Locked
  • Question Question
Design, Fab, & Inspection Requirements for non-Code "Vessel"?
Replies
4
Views
337
KernOily
KernOily
loilfan
  • Locked
  • Question Question
UG-36(c)(3)(-b)
2
Replies
20
Views
3K
loilfan
loilfan
kurtz
  • Locked
  • Question Question
Fatigue analysis - ASME and EN 13445
Replies
15
Views
2K
MrPDes
MrPDes
Mark1arm
  • Locked
  • Question Question
Acceleration Loadings
Replies
4
Views
178
NRP99
NRP99
PVTC
  • Locked
  • Question Question
UHA-51(g) - Exemption From Impact Testing Because of Low Stress.
Replies
1
Views
318
SnTMan
SnTMan
stan000
  • Locked
  • Question Question
two welding PQR procedure( SAME GROUP) can add thickness
Replies
7
Views
248
pradipgoswami
pradipgoswami
Rspain
  • Locked
  • Question Question
Correct sizing of Deaerator's safety valve - fatal failure of boiler check valve
Replies
3
Views
282
Rspain
Rspain
itsvkarthik
  • Locked
  • Question Question
Tangential Support Lugs
Replies
4
Views
188
racookpe1978
racookpe1978
taba94
  • Locked
  • Question Question
discrepancy between fig ucs-66 and fig ucs66.1
Replies
2
Views
99
SnTMan
SnTMan
MOHAMMED89
  • Locked
  • Question Question
Hydrotesting for ASME Sec. VIII Vessel.
Replies
4
Views
177
oknow
oknow
MixBlender
  • Locked
  • Question Question
Blowdown vessel water inlet distinctions - Clarification needed
Replies
2
Views
132
MJCronin
MJCronin
stan000
  • Locked
  • Question Question
insulation pins
Replies
2
Views
519
stan000
stan000
Paulettea
  • Locked
  • Question Question
Post Forming Heat Treatment Requirement
Replies
6
Views
555
r6155
r6155
adilmn
  • Locked
  • Question Question
Hydrojetting pressure calculation for Exchanger
Replies
3
Views
512
SnTMan
SnTMan
Paulettea
  • Locked
  • Question Question
Creep and Fatigue (Ratchet) interaction
Replies
4
Views
326
TGS4
TGS4
NovaStark
  • Locked
  • Question Question
Design validation of rectangular tank using asme
Replies
5
Views
661
NovaStark
NovaStark
Rakesh2560
  • Locked
  • Question Question
Material for flue gas stack
Replies
3
Views
437
MJCronin
MJCronin
pradeep4u
  • Locked
  • Question Question
pressurizing deaerator
Replies
2
Views
135
Dhurjati Sen
Dhurjati Sen
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top