Why are the Miata front UCA pivot axes tilted inward? 1

[NoahLKatz]

I'm looking at using the nice aluminum front control arms from an NC or ND Miata for my reverse trike.

I'm not sure if they've kept geometry similar to the NB Miata front suspension pictured below (the only Miata suspension 3D model I could find), but in any case the UCA's axes are tilted inward by about 2 1/2 deg.

I'm sure the Mazda engineers had a good reason for doing this, but what is it?

The arms are also tilted about the transverse axis about 4 1/2 deg for anti-dive, which besides doing that also seems nice in that it counteracts loss of caster from the remaining nose dive, But the semi-trailing component does the opposite.

Besides that, is a paltry 2 1/2 deg worth the extra frame construction complexity?

 

[BrianPetersen]

Building in that angle doesn't change complexity at all. The angle gets built into the design of the stampings, and the stamping tool(s) won't care.

The angle is there because some suspension engineer at Mazda went through an optimisation routine for how they wanted the antidive and the caster to change with suspension travel to achieve whatever objectives they set for themselves, and this is what the optimisation routine spat out. Lots of modern suspension designs have pivot axes at all sorts of 3-D angles which are tough to analyse with pencil and paper, but nowadays it isn't done with pencil and paper, it's done in 3-D models.

If you're re-using parts, presumably you're using your own chassis attachment points. There's no need to maintain Mazda's angles as long as whatever you do, doesn't cause binding or other such troubles. Re-running Mazda's optimisation routine but customised for your own vehicle would probably result in different recommendations for which way the pivot axes go ... but I'm thinking you don't have that!

I wouldn't worry too much about it. Get it somewhere close, and build in some adjustment.

 

[NoahLKatz]

> There's no need to maintain Mazda's angles as long as whatever you do, doesn't cause binding or other such troubles.

Glad to hear that, thanks for explaining.

> presumably you're using your own chassis attachment points.

Yes, which is why it does change the complexity; it either adds angles to frame tubes, or results in an asymmetric mounting bracket.

 

[BrianPetersen]

Aye, I was thinking about complexity from Mazda's point of view, and you're thinking about it from yours. I would be tempted to use a shimmed mount for the upper control arm so that you can have adjustable caster (via shimming the UCA mounts unequally front to rear).

And then there are things like this ... https://www.fulltiltstreetrods.com/front-suspension-intro.html

(and there are many other sources)

 

[NoahLKatz]

> I would be tempted to use a shimmed mount for the upper control arm so that you can have adjustable caster (via shimming the UCA mounts unequally front to rear).

The Miata has caster/camber adjustmet via eccentric bolts on the (L-shaped) LCA chassis mounting points, but I think it's just a couple of degrees.

I could add more by making the UCA chassis clevises wider and filling the gaps with different thickness spacers.

> And then there are things like this ... https://www.fulltiltstreetrods.com/front-suspension-intro.html

The trouble with those is that they're pricey and overweight for my project, a V-twin powered reverse trike that I expect to weigh about 1000 pounds.

 

[NoahLKatz]

> Building in that angle doesn't change complexity at all. The angle gets built into the design of the stampings, and the stamping tool(s) won't care.

So are stamping dies now made with CNC, and tool and die makers are an extinct species?

 

[BrianPetersen]

> Building in that angle doesn't change complexity at all. The angle gets built into the design of the stampings, and the stamping tool(s) won't care.

So are stamping dies now made with CNC, and tool and die makers are an extinct species?

Yes, on the CNC (and that's been the case for a couple of decades). Still need people with tool and die experience to get them right ...

Can-Am Spyder front suspension https://www.pieces-can-am.fr/canam-moto/SPYDER/2023/SPYDER-RT/05-Suspension--Front/4855/29/0/4855

Looks from the diagram like they have anti-dive geometry built in. Friend of mine has one. I'll see about taking a look at it.

 

[NoahLKatz]

> Can-Am Spyder front suspension https://www.pieces-can-am.fr/canam-moto/SPYDER/2023/SPYDER-RT/05-Suspension--Front/4855/29/0/4855

Interesting, thanks.

I'm not too crazy about the narrow-based chassis mount points, and I like the impact absorption benefits of the Miata's L-shaped LCA's; it might have been you who educated me about that a couple of years ago.