Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!
Sectioning
- Thread starter drbauer
- Start date
ASME Y14.3-2003:
4.3 Nonsectioned Items in the Cutting Plane
4.3.1 Sectioning Assembled Items. When the cutting
plane lies along the longitudinal axis of items, such as
shafts, bolts, nuts, rods, rivets, keys, pins, screws, ball
or roller bearings, gear teeth, spokes, and the like, these
parts are not sectioned except when internal construction
is shown. See Fig. 47.
4.3.2 Conventional Section Lining of View. Where the
cutting plane is perpendicular, or cuts across the items
in para. 4.3.1, the sectional view is section lined in the
usual manner.
"Wildfires are dangerous, hard to control, and economically catastrophic."
Ben Loosli
Sr IS Technologist
L-3 Communications
4.3 Nonsectioned Items in the Cutting Plane
4.3.1 Sectioning Assembled Items. When the cutting
plane lies along the longitudinal axis of items, such as
shafts, bolts, nuts, rods, rivets, keys, pins, screws, ball
or roller bearings, gear teeth, spokes, and the like, these
parts are not sectioned except when internal construction
is shown. See Fig. 47.
4.3.2 Conventional Section Lining of View. Where the
cutting plane is perpendicular, or cuts across the items
in para. 4.3.1, the sectional view is section lined in the
usual manner.
"Wildfires are dangerous, hard to control, and economically catastrophic."
Ben Loosli
Sr IS Technologist
L-3 Communications
namdac,
You are correct, but the thread is about sectioning.
Chris
Systems Analyst, I.S.
SolidWorks 06 4.1/PDMWorks 06
AutoCAD 06
ctopher's home (updated 06-21-06)
You are correct, but the thread is about sectioning.
Chris
Systems Analyst, I.S.
SolidWorks 06 4.1/PDMWorks 06
AutoCAD 06
ctopher's home (updated 06-21-06)
The screw thread issue came up in thread1103-159528
ASME Y14.6-2001 para 3.2 addresses the issue of whether to reference the thread standard.
It then gives examples of the thread spec as part of the callout.
But as Ctopher says this is a bit off topic.
ASME Y14.6-2001 para 3.2 addresses the issue of whether to reference the thread standard.
It then gives examples of the thread spec as part of the callout.
But as Ctopher says this is a bit off topic.
Multi and Secional View Drawings ASME/ANSI Y14.3
Section 3-4.3.1 - Where the cutting plane lies along the longitudinal axis of items such as shafts, bolts, nuts, rods, rivets, keys, pins, screws, ball or roller bearings, gear teeth, spokes and the like, these parts are not sectioned except where internal construction must be shown.
Best Regards,
Heckler
Sr. Mechanical Engineer
SW2005 SP 5.0 & Pro/E 2001
Dell Precision 370
P4 3.6 GHz, 1GB RAM
XP Pro SP2.0
NVIDIA Quadro FX 1400
o
_`\(,_
(_)/ (_)
Never argue with an idiot. They'll bring you down to their level and beat you with experience every time.
Section 3-4.3.1 - Where the cutting plane lies along the longitudinal axis of items such as shafts, bolts, nuts, rods, rivets, keys, pins, screws, ball or roller bearings, gear teeth, spokes and the like, these parts are not sectioned except where internal construction must be shown.
Best Regards,
Heckler
Sr. Mechanical Engineer
SW2005 SP 5.0 & Pro/E 2001
Dell Precision 370
P4 3.6 GHz, 1GB RAM
XP Pro SP2.0
NVIDIA Quadro FX 1400
o
_`\(,_
(_)/ (_)
Never argue with an idiot. They'll bring you down to their level and beat you with experience every time.
- Status