designerabc
Mechanical
We are trying to edit a view break that was created in NX7.5. After our update to NX9, we are unable to edit the view.
Can anyone assist me with this?
Thanks,
Jodie
Can anyone assist me with this?
Thanks,
Jodie
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!
NX9 View Broken Edit
- Thread starter designerabc
- Start date
- Status
- Thread starter
- #3
designerabc
Mechanical
Thank you... but broken legacy is not in my list to pick...
Is the picture visible to you in the last post? (it may be blocked by your company firewall)
It shows where to find the command to add it to your menu.
www.nxjournaling.com
It shows where to find the command to add it to your menu.
www.nxjournaling.com
- Thread starter
- #5
designerabc
Mechanical
I saw where to add it - but that was NX8.5. In NX9 there is not a legacy in the command.
The picture shows where to find it in the customize command; it shows NX 8.5, but the NX 9 location is the same.
www.nxjournaling.com
www.nxjournaling.com
- Thread starter
- #8
Similar (ish) question,
When using the new broken view in NX8.5, with dimensions, a few engineers have reported an error "the view break will result in hidden annotations" and the dimensions disappear.
I know there's a problem with using broken view and then sectioning it, where the section line will disappear (and a similar warning is given).
Vaguely remember someone saying this is fixed in a later release.
But has anyone seen the error with dimensions vanishing from the new broken views, and is there a workaround?
For the minute I've just told people to use the legacy broken view, but it would be good to use the new one.
Thanks, Carl
NX 8.5 with TC 8.3
When using the new broken view in NX8.5, with dimensions, a few engineers have reported an error "the view break will result in hidden annotations" and the dimensions disappear.
I know there's a problem with using broken view and then sectioning it, where the section line will disappear (and a similar warning is given).
Vaguely remember someone saying this is fixed in a later release.
But has anyone seen the error with dimensions vanishing from the new broken views, and is there a workaround?
For the minute I've just told people to use the legacy broken view, but it would be good to use the new one.
Thanks, Carl
NX 8.5 with TC 8.3
Carl,
I've submitted a PR against this issue in NX9. I was told (unbelievably) that it has been moved to an ER.
In my case, it's when you add a centerline to the broken view. Any model updates trigger a view update and then the centerline gets hidden. Along, of course, with any dimensions that are attached to the centerline.
The work around, according to development, is to make use of the legacy function.
NX 9.0.3.4
NX 10 (Testing)
Windows 7 64 (Windows 8.1 Tablet)
I've submitted a PR against this issue in NX9. I was told (unbelievably) that it has been moved to an ER.
In my case, it's when you add a centerline to the broken view. Any model updates trigger a view update and then the centerline gets hidden. Along, of course, with any dimensions that are attached to the centerline.
The work around, according to development, is to make use of the legacy function.
NX 9.0.3.4
NX 10 (Testing)
Windows 7 64 (Windows 8.1 Tablet)
JohnRBaker
Mechanical
We've been over this ground before phillpd and NOTHING has changed in the MONTH since this was last discussed:
John R. Baker, P.E.
Product 'Evangelist'
Product Engineering Software
Siemens PLM Software Inc.
Industry Sector
Cypress, CA
Siemens PLM:
UG/NX Museum:
To an Engineer, the glass is twice as big as it needs to be.
John R. Baker, P.E.
Product 'Evangelist'
Product Engineering Software
Siemens PLM Software Inc.
Industry Sector
Cypress, CA
Siemens PLM:
UG/NX Museum:
To an Engineer, the glass is twice as big as it needs to be.
Phillip and John,
Thank you both for the info, yes that's the workaround I've suggested as well.
It will be useful when the new view break is able to handle annotations and sectioning etc. ... anyone able to test it in NX10?
Regards, Carl
NX 8.5 with TC 8.3
Thank you both for the info, yes that's the workaround I've suggested as well.
It will be useful when the new view break is able to handle annotations and sectioning etc. ... anyone able to test it in NX10?
Regards, Carl
NX 8.5 with TC 8.3
JohnRBaker
Mechanical
That issue has not yet been addressed, and that includes NX 10.0.
John R. Baker, P.E.
Product 'Evangelist'
Product Engineering Software
Siemens PLM Software Inc.
Industry Sector
Cypress, CA
Siemens PLM:
UG/NX Museum:
To an Engineer, the glass is twice as big as it needs to be.
John R. Baker, P.E.
Product 'Evangelist'
Product Engineering Software
Siemens PLM Software Inc.
Industry Sector
Cypress, CA
Siemens PLM:
UG/NX Museum:
To an Engineer, the glass is twice as big as it needs to be.
Thanks John, in that case I'll put something together for people that ask about it.
Regards Carl
NX 8.5 with TC 8.3
Regards Carl
NX 8.5 with TC 8.3
Finally had time to test this, and I agree with Phil it does seem to be centrelines which don't work with break view.
One of our engineers has suggested another workaround, which is to show centrelines from the model instead of including them in drafting, which of course works fine.
NX 8.5 with TC 8.3
One of our engineers has suggested another workaround, which is to show centrelines from the model instead of including them in drafting, which of course works fine.
NX 8.5 with TC 8.3
- Status