NX 8.5 rumors

[cubalibre000]

Hi,
Siemens PLM is developing NX 8.5.
NX 8 will be compatible with NX 8.5 or NX 8.5 will open NX 8 files but not viceversa ?

Thank you...

Using NX 8 and TC8.3

 

[JohnRBaker]

If you ignore the 'format' of the numbers and simply think of NX 8.5 like ANY other 'major' release, as it was with NX 5.0, NX 6.0, NX 7.0, NX 7.5 and NX 8.0, you will not have any problems.

Now officially you NEVER actually heard me talk about NX 8.5 as if it really existed, right ;-)

John R. Baker, P.E.
Product 'Evangelist'
Product Engineering Software
Siemens PLM Software Inc.
Industry Sector
Cypress, CA

http://www.siemens.com/plm

UG/NX Museum:

http://www.plmworld.org/p/cm/ld/fid=209

To an Engineer, the glass is twice as big as it needs to be.

 

[topgun101]

Hi John,
Is there any non official date for the release of NX8.5?
I am planning on a February deployment of Teamcenter 9.1 and NX8.0
But if I only need to hold back a couple on months, then it may be better to hold off. Or should I take this off-line and discuss with our SiemensPLM rep.

Thanks

TonyC (ex Australian user group) now in NZ

 

[JohnRBaker]

For the last several years, the period of time between major releases has been approximately 12 months, give or take a month.

Do I need to say anything more?

John R. Baker, P.E.
Product 'Evangelist'
Product Engineering Software
Siemens PLM Software Inc.
Industry Sector
Cypress, CA

http://www.siemens.com/plm

UG/NX Museum:

http://www.plmworld.org/p/cm/ld/fid=209

To an Engineer, the glass is twice as big as it needs to be.

 

[Arkance/PhoeNX]

@topgun101, Tony you are way to keen!

Anthony Galante
Technical Resource Coordinator

NX4.0.4MP10, NX5.0.0->5.0.6, NX6.0.0->NX6.0.5, NX7.0.0->NX7.0.1 & NX7.5.0.32-> NX7.5.4.4, Beta NX8.0.0.25

 

[RUGmechanic]

I can wait 5 or 6 months
Just to check: There will still be a 32bit version?

Older budweiser

 

[JohnRBaker]

For now, but the clock IS running down on that one...

John R. Baker, P.E.
Product 'Evangelist'
Product Engineering Software
Siemens PLM Software Inc.
Industry Sector
Cypress, CA

http://www.siemens.com/plm

UG/NX Museum:

http://www.plmworld.org/p/cm/ld/fid=209

To an Engineer, the glass is twice as big as it needs to be.

 

[cubalibre000]

Hi RUGmechanic,
NX 8 release notes say that will be the last release that support 32 bit architecture.
Se the attached image.
For this I post this rumors, to have some date and explication.

Thank you...

Using NX 8 and TC8.3

 

[JohnRBaker]

If you read carefully, the NX 8.0 releases notes actually contains TWO different statements about the move to 64-bit only versions of NX. One of these statements is accurate, the other is not. I think there will be some clarification in the release notes for NX 8.0.1.6.

John R. Baker, P.E.
Product 'Evangelist'
Product Engineering Software
Siemens PLM Software Inc.
Industry Sector
Cypress, CA

http://www.siemens.com/plm

UG/NX Museum:

http://www.plmworld.org/p/cm/ld/fid=209

To an Engineer, the glass is twice as big as it needs to be.

 

[looslib]

Th image posted states that NX9 will only be supported on 64-bit hardware. It also says that NX8 will be the last supported on 32-bit on Windows.


"Wildfires are dangerous, hard to control, and economically catastrophic."

Ben Loosli

 

[JohnRBaker]

Based on the substance of this thread, it's obvious that only ONE of those statements can be correct.

John R. Baker, P.E.
Product 'Evangelist'
Product Engineering Software
Siemens PLM Software Inc.
Industry Sector
Cypress, CA

http://www.siemens.com/plm

UG/NX Museum:

http://www.plmworld.org/p/cm/ld/fid=209

To an Engineer, the glass is twice as big as it needs to be.