Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!
countersink question 2
- Thread starter aero101
- Start date
-
1
- #2
"Art without engineering is dreaming; Engineering without art is calculating."
Have you read faq731-376 to make the best use of these Forums?
I would think that would be determined by the spec of whats going in the hole (screw?) and thickness of material. Our company has a guide designers use to determine what the range of the countersunk hole should be and min. material thickness for screws & rivets.
My point is that standard information is readily available, people have been doing it for years. BigJimbo, you bring up good points.
"Art without engineering is dreaming; Engineering without art is calculating."
Have you read faq731-376 to make the best use of these Forums?
"Art without engineering is dreaming; Engineering without art is calculating."
Have you read faq731-376 to make the best use of these Forums?
-
1
- #5
Check out Machineries, if nothing else they have the dimension for the fasteners from which you can extrapolate the correct countersink based on function.
However, are you sure you want 90° & 1/4?
Whey you say 1/4 do you mean a 1/4 inch screw? Inch fasteners don't have 90° heads, they have 8° or 100° unless a custom special.
Think long and hard about your function, bigjimbo makes a good point about material thickness. You also need to consider if the mating part has threaded holes or if you're using nuts. If threaded holes then you have a problem as both the head and the thread are fixed and cannot float. There are workarounds for this if your functional requirement is just to keep the heads flush or under flush, however they have stress and aesthetic implications.
However, are you sure you want 90° & 1/4?
Whey you say 1/4 do you mean a 1/4 inch screw? Inch fasteners don't have 90° heads, they have 8° or 100° unless a custom special.
Think long and hard about your function, bigjimbo makes a good point about material thickness. You also need to consider if the mating part has threaded holes or if you're using nuts. If threaded holes then you have a problem as both the head and the thread are fixed and cannot float. There are workarounds for this if your functional requirement is just to keep the heads flush or under flush, however they have stress and aesthetic implications.
Posting guidelines faq731-376 (probably not aimed specifically at you)
What is Engineering anyway: faq1088-1484
What is Engineering anyway: faq1088-1484
PeterStock
Mechanical
82° or 100° for inch flat head screws
Peter Stockhausen
Senior Design Analyst (Checker)
Infotech Aerospace Services
Peter Stockhausen
Senior Design Analyst (Checker)
Infotech Aerospace Services
- Thread starter
- #7
- Thread starter
- #8
Why on earth are you using a countersink with a button head cap screw?
Posting guidelines faq731-376 (probably not aimed specifically at you)
What is Engineering anyway: faq1088-1484
What is Engineering anyway: faq1088-1484
- Thread starter
- #10
Sorry aero, your question doesn't make sense.
You don't usually use countersinks with a button head screw. A countersink is generally used to recess a flat head screw.
If you mean counterbore dia then .285 sounds far too small.
If you just mean what hole size you need, then you need to calculate this based on function. .285 isn't unreasonable so long as it meets your requirement and the tollerances of position on the holes and the mating parts are set appropriately. I think the suggested normal clearance holes for 1/4" in Machineries is .281 which I believe corresponds to a fairly standard counterbore tool.
So, with the information you present I have no way of telling you if .285 is acceptable.
You don't usually use countersinks with a button head screw. A countersink is generally used to recess a flat head screw.
If you mean counterbore dia then .285 sounds far too small.
If you just mean what hole size you need, then you need to calculate this based on function. .285 isn't unreasonable so long as it meets your requirement and the tollerances of position on the holes and the mating parts are set appropriately. I think the suggested normal clearance holes for 1/4" in Machineries is .281 which I believe corresponds to a fairly standard counterbore tool.
So, with the information you present I have no way of telling you if .285 is acceptable.
Posting guidelines faq731-376 (probably not aimed specifically at you)
What is Engineering anyway: faq1088-1484
What is Engineering anyway: faq1088-1484
1/4 clearance holes could be .257 (Close fit), .266 (Free fit), or .281 (Loose fit)... depending on what your application needs.
If you are talking counterbores instead of countersinks, then .285 is too small as maximum head diameter on a 1/4 buton head cap screw is .437
You should buy Machinery's Handbook or reference one.
"Art without engineering is dreaming; Engineering without art is calculating."
Have you read faq731-376 to make the best use of these Forums?
If you are talking counterbores instead of countersinks, then .285 is too small as maximum head diameter on a 1/4 buton head cap screw is .437
You should buy Machinery's Handbook or reference one.
"Art without engineering is dreaming; Engineering without art is calculating."
Have you read faq731-376 to make the best use of these Forums?
- Thread starter
- #13
- Status
Similar threads
- Locked
- Question
- Locked
- Question