Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: kltex
  • Order by date
  1. kltex

    Amada - Edge and Approach

    Thanks What about fine edge?
  2. kltex

    Amada - Edge and Approach

    Can anyone help me solve the pazzle, Edge and Approach data When does each come into action?
  3. kltex

    Making a faster mild steel cut - Amada

    My laser has 2000W, but I will try to replace the lense with a 7.5" and use smaller nozzle
  4. kltex

    Making a faster mild steel cut - Amada

    I was cutting 6mm mild steel the other day, and the cut was good enough. Power was only 1100 and speed was 1500. This was the maximum speed I could run at this power level. I figured I could rise the power and gain some more speed, but no matter what i did, I could not get a clean cut with...
  5. kltex

    Spatter on bottom of lens

    Laserninja do you have a matrix for 2kw?
  6. kltex

    Amada 2415 How to cut ABS?

    Great cut, but the important picture is the one with the cutting parameters :)
  7. kltex

    MDF wood on an AMADA FO3015 Laser??????

    But keeping the head high by "lying" on the thickness will put the focus point way off your intended point. Why not just add the inches to the nozzle gap?
  8. kltex

    MDF wood on an AMADA FO3015 Laser??????

    mikeybob125,your settings shows thickness 1.16" but you are only cutting 0.75". Are you using this clearance to keep the nozzle above the wood because the height sensor isn't working? Will it be correct to guess that the total nozzle gap will be 0.06"+(1.16"-0.75")?
  9. kltex

    LCV 3015 Bll - Assist Gas Problem

    Did you check the inline gas filters?
  10. kltex

    Amada 2415 How to cut ABS?

    The machine I bought came without any cutting parameters for plastics - only for metals. I did try to cut 1" round test circles from the ABS a few days ago and the result was catastrophic. At first the laser did not pierce the ABS and the cut was made only half way deep, the amount of smoke...
  11. kltex

    Amada 2415 How to cut ABS?

    Anyone? Anything? Some sort of starting point?
  12. kltex

    Amada 2415 How to cut ABS?

    What parameters should I set to cut 10mm ABS?
  13. kltex

    Help with cutting parameters

    Our story starts yesterday when I spent 4 hours trying to get a clean cut on a 6mm stainless steel. After 4 hours with no luck, I had to do something, I had to start cutting. So, I did. The cuts came out black with sharp burr and all dirty with splatter. But at least I made the cut. So today...
  14. kltex

    Help with cutting parameters

    Foostrap you are right ! problem solved, tell you all about it later today.
  15. kltex

    Help with cutting parameters

    Well, apparently my pierce conditions were wrong, and now with your parameters the pierce is much cleaner and faster. Attached are the new pierce condition 103 And a sample cut with this pierce But that does not solve the black cutting surface. I am trying to think outside of the box, maybe...
  16. kltex

    Help with cutting parameters

    I never paid special attention to the pierce. Always thought: if it goes all the way thru - its good enough. I will take some pictures of my pierce (only tomorrow) but from what i remember its quiet with sparks going in all directions for about 3-4 sec. Even if the pierce is good (or bad) why...
  17. kltex

    Help with cutting parameters

    Not a very good day today. I started the morning with 4 hours of trials to set up new parameters. Ended up with something not as good as I had but a bit faster 700cm/min instead of 500cm/min. Tried my old settings again, and it did not cut as clean as it did on the first time Nitrogen pressure...
  18. kltex

    Help with cutting parameters

    I found all those parameters the hard way. It took me several hours and more then 30 pcs of trial cuts to achieve a really clean cut. All those testing were done when the machine was only a few days old, and I had no idea how and what should I change to make it work. Tomorrow I am starting a new...
  19. kltex

    Help with cutting parameters

    laserdog, I'm hoping to hear from you soon

Part and Inventory Search