Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. jerry1423

    Splines Behind the Part in a Drawing

    I hope this is the issue. RMC on drawing view and go to Settings. Jerry J. UGV5-NX1899
  2. jerry1423

    Splines Behind the Part in a Drawing

    I assume it has to do with Clip Planes. I am not at work now, so I will try to get back to you later with a solution. Jerry J. UGV5-NX1899
  3. jerry1423

    WAVE Linking/publications in NX

    Sorry about the delay getting back to you. The first two are pdf's. The bottom ones are videos. https://www.appliedcax.com/docs/portland-nx-users-day-April-2018/NX-Assembly-WAVE-Link-Demo-and-Tips.pdf https://www.swooshtech.com/2021/02/12/wave-geometry/...
  4. jerry1423

    NX - Location of all Keyboard Shortcuts

    Maybe this will help you. https://community.sw.siemens.com/s/article/nx-shortcut-keys-view-full-list-and-create-custom-keys Jerry J. UGV5-NX1899
  5. jerry1423

    Is that possible drop down box in NX drafting?

    Maybe this post will help you. https://community.sw.siemens.com/s/question/0D5KZ000009ASzZ0AW/creating-a-dropdown-list-in-draft Jerry J. UGV5-NX1899
  6. jerry1423

    Need to calculate least size bounding box REGARDLESS of coordinate system

    I found this on YouTube pertaining to what Cowski mentioned above. I am very interested in learning it, but it does not mention what version of NX was used in the video. https://www.youtube.com/watch?v=ZjvO3zT-89U Jerry J. UGV5-NX1899
  7. jerry1423

    WAVE Linking/publications in NX

    You will probably get good results searching in YouTube each of the four bullet points that you mentioned. I will try to get back to you when I have more time. Jerry J. UGV5-NX1899
  8. jerry1423

    Learning How to Type

    I am sixty years old and never learned how to type properly. I am still just a pecker. Does anybody have any suggestions on the best way to learn to type ? Jerry J. UGV5-NX1899
  9. jerry1423

    Native NX to Solid Edge

    It appears that it can, but I am not certain of that. If you go to the below link and read under "There are two ways to open a NX part file in Solid Edge:" you should be able to find what you are looking for. https://www.soliddna.com/SEHelp/ST5/EN/i_v/ugse1a.htm Jerry J. UGV5-NX1899
  10. jerry1423

    How can 2 truncated cones with different drafting directions be combined tangentially?

    They can't, you will need to figure out how to add material for them to join to. A few thousandths will work. Jerry J. UGV5-NX1899
  11. jerry1423

    In my latest version of NX it takes

    Here is something that I found that may help you. https://community.sw.siemens.com/s/question/0D54O000083Yc0USAS/slow-postprocessing Jerry J. UGV5-NX1899
  12. jerry1423

    In my latest version of NX it takes

    A couple questions: What version of NX are you on? Are you on Teamcenter? Jerry J. UGV5-NX1899
  13. jerry1423

    In my latest version of NX it takes

    It will take a longer amount of time to save the first time the file is saved in the new version NX, but the save after that you should see an improvement. Let us know if that is not the situation here. Jerry J. UGV5-NX1899
  14. jerry1423

    NX unite and subtract reversed!

    Run EXAMINE GEOMETRY on all the solid bodies before and after the unites or subtractions that you do. Jerry J. UGV5-NX1899
  15. jerry1423

    why NX can not use some installed fonts in drafting?

    Why is your font gap zero ? Jerry J. UGV5-NX1899
  16. jerry1423

    why NX can not use some installed fonts in drafting?

    Maybe this will help you. When you open the page verify it is expanded. https://community.sw.siemens.com/s/question/0D54O00006gPSdfSAG/drafting-standard-text-font Jerry J. UGV5-NX1899
  17. jerry1423

    Define Deformable Part

    Here is a video that I enjoyed and may help you with your issue. https://www.youtube.com/watch?v=TGNQR-mqrl4 Jerry J. UGV5-NX1899
  18. jerry1423

    Measure COG

    I believe the issue here is you want the COG to be measured relative to another CSYS such as the WCS. After the associative point is placed on the COG you can use the Measure Tool to get what you want. Jerry J. UGV5-NX1899
  19. jerry1423

    Measure COG

    Do you know how to place an associative point at the COG so you can see exactly where it is ? Jerry J. UGV5-NX1899
  20. jerry1423

    Moving a face

    Yes, I tried pulling the face and I got the same result. Thanks for the suggestion. Jerry J. UGV5-NX1899

Part and Inventory Search

Back
Top