Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. deeptuna

    Purchasing CMM

    Old IE, Look into renting or leasing a CMM. It turned out better in the short and long run for a corp i was familiar with. Also liked the B&S Just a thought.
  2. deeptuna

    drilling grade 8.8 metric bolt

    Hello Scott, One other though that seems nobody mentioned here. Try EDM machining. They could punch small holes in high tensile steel such as the 1 u have. Obviously you have to look at the economics of drill vs EDM.
  3. deeptuna

    NPT threads VS PT VS BSPT

    Hello All, I am inquiring about what standards do Japanese PT fall under? or what types of threads to I select when I want to threads to be compatable w/ the Japanese PT threads? I also used BSPT British Std Taper Pipe Thread in PT type locations but was unsure of the fit. Was this correct...
  4. deeptuna

    Brazing .030" thick Aluminum

    Bri72, Did you try brazing in a furnace? Also what about backing/fixturing the tube so it does not move. Regards, DeepTuna
  5. deeptuna

    Hi Temp O-Rings - >500F Air

    Tellier, Yeap, your could try Perfluoroelastomers or other pricey elastomers. From my experience they get pricey after silicone. You could try increasing the number of seals (2 orings), using a different cross section (such as an x cross section type seal) or larger diameter (more material to...
  6. deeptuna

    how to make a standard woodruff keywey

    Check the machinery handbook -DeepTuna
  7. deeptuna

    Remote a std 3.5" 1.44MB flpy dsk drv

    There is a good post on this subject that basically summarizes the primary question in Hardware Arch forum Thanks, DT
  8. deeptuna

    remotely connect a standard 3.5" 1.44MB floppy

    Thanks BPatt for the great post, Its looks like our design is steering towards the USB SCSI interface direction. We have yet to finallize the Computer involved so this is the direction we are looking into. This is also posted in the Comm & Signal Processing Forum I will post with the final...
  9. deeptuna

    designing a parallel- port interfaced motor position controller

    Also check a book called "Controlling your world with your PC" - Bergman it describes a step by step approach to parallel and other cheap comm w/ steppers, relays etc Good Luck
  10. deeptuna

    Remote a std 3.5" 1.44MB flpy dsk drv

    Preferably prefer as a transparant application such as the built in model. Could use the disk drive as a dump/read to access files? Modification of the source code is not the preferred method ie more s/w writing and additional testing. What is the distance that I could use for a floppy from a...
  11. deeptuna

    remotely connect a standard 3.5" 1.44MB floppy

    Hello All and Great Site/Forum, Looking for a way to remotely connect a standard 3.5" 1.44MB floppy disk drive approx 75 ft away (maybe distance may be reduced to 25ft) from a computer. Would prefer a card interface but may in the future may have (1) serial or (1) ethernet port to work...
  12. deeptuna

    Remote a std 3.5" 1.44MB flpy dsk drv

    Hello All and Great Site/Forum, Looking for a way to remotely connect a standard 3.5" 1.44MB floppy disk drive approx 75 ft away (maybe distance may be reduced to 25ft) from a computer. Would prefer a card interface but may in the future may have (1) serial or (1) ethernet port to work...

Part and Inventory Search

Back
Top