Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. Umhoefer

    QS9000 Lab Scope

    My problem stems from the incorperation of a measurement lab for dimensional layouts and spectometer readings, etc. I work for a company that has been QS9000 certified for the last 3 years but now we need to add a labratory to our documantation. Does anyone have any idea where i may find an...
  2. Umhoefer

    Retrofitting CMM

    Dear Old IE, Have you checked out www.atiquality.com? They have several new and used units. Regards, G. Umhoefer
  3. Umhoefer

    Reducing Low Frequency transmissions through residential walls

    Thanks for clearing that up. As you can tell this is definitely not my field of expertise. Thanks again for the assistance Sincerely, G. Umhoefer
  4. Umhoefer

    Reducing Low Frequency transmissions through residential walls

    Paulism, What you recomend sounds like a product i've seen used on cars called Dynamat. However this product is very expensive, is the material you refer to commonly refered to by it's commercial name. Example; soem people i know still refer to coppiers as Xerox machines after the brand that...
  5. Umhoefer

    Net Beui

    Thanks for the advice. Using tellnet and the ping comand we found one bad switch and the router was going bad. We replaced both and everything works great. Thanks once again.
  6. Umhoefer

    ESTIMATION OF UNCERTAINTY OF MEASUREMENT

    Are you looking for a Gage R&R form that crunches the data for you? If so i may have something you could use. If your interested reply with your e-mail address and i will e-mail you a copy.
  7. Umhoefer

    Net Beui

    Hello, I have heard that running Net Beui on a lan may cause conflicts. We are expirencing packet loss on the way to the router (LAN Network with simple switch router) and wonder if the Net Beui setting may be to blame. Any one have any ideas?
  8. Umhoefer

    Reducing Low Frequency transmissions through residential walls

    I found a need to reduce the amount of low frequency (subwoofer produced) audio waves that get transmitted through my townhouse walls into my neighbors house. He has the same problem, so we would like to know if there is a somewhat affordable way of acousticly deadening the connecting wall...
  9. Umhoefer

    Can I Replace Hub With Switch

    Thanks, that was our thinking. It's really nice to be able to get support when you need it. Thanks Again, G.Umhoefer
  10. Umhoefer

    Can I Replace Hub With Switch

    My partner and i inhearited a old network at our company when the IT Manager retired. We have two old (and dying)12port 10/100 hubs and one 12port 10/100 switch at the heart of our network. Into which a router and two servers feed. The "heart" feeds into local hubs at the general...
  11. Umhoefer

    Flagnoting every print dimension - bad drafting practice?

    Hi VP of Quality, I agree that the Quality Dept. should definetly do there own numbering. It is typicaly the Quality department who performs dimensional and capability studies, and handles the initial flack from a out of tollerance dimensions. So it just makes sense that they number the...
  12. Umhoefer

    Flagnoting every print dimension - bad drafting practice?

    Gianfranco, It's good to see someone agrees with me. However it should be noted that I do also feel that if you can make simpler prints that only show the needed dimensions by all means this is the way to go. An inspector should have the easiest work instruction possible for a given job, as to...
  13. Umhoefer

    Flagnoting every print dimension - bad drafting practice?

    In my field "ballooning" of a drawing is common practice. Every attribute is identified and compared to the actual part. It is also how we identify all SPC dimensions making it easier for the inspectors to find and measure the correct feature. This practice causes very little...
  14. Umhoefer

    Lost Ends

    Thanks Laffalot, Your suggestion is helpfull and that is what i have started doing only a little more in the reverse. We have everyone up and started pulling connections off the hub. It made for a tense day of complaints but we narrowed down who is where. Wouldn't it be better to have one...
  15. Umhoefer

    Lost Ends

    I have been asigined to track down and map all the network wires. I am looking for equipment that i can use to find where specific CAT 5 wires go. We have about 45 stations on the network with 5 mini hubs on the plant floor and 3 hubs with one main switch in my office. Do to an almost...
  16. Umhoefer

    What's the best Graphic Viewer

    Hello, I know that many people have voiced there opion on what is the best CAD package out there. My question is what is the best system for the money to simply view, dimension, compute volumes, and digitize a 3d object. We are a third tier automotive supplier and seldom if ever do any...
  17. Umhoefer

    Polarized Polycarbonate resin

    Have you tried the GE Plastics website. Also i have found calling them directly to be very usefull Regards; Gumhoefer
  18. Umhoefer

    laser Etching

    I work for a company that molds paints then laser etches plastic parts for the automotive industry. Depending on the type of paint, we use a wide range, lasering should be fairly easy. Will you be etching down to a previous layer of paint I.E. the graphic color, or to the plastic part it self...
  19. Umhoefer

    Locating an out of house metrology lab

    I work in the chicago land area (U.S.A.), and am searching for a out of house metrology lab to do dimensional layouts on plastic parts. These parts are mainly for the automotive industry, so Q.S. 9000/ ISO 9002 is a must. Any help or adivce would be welcome.

Part and Inventory Search

Back
Top