Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. Milkboy

    Carbon Graphite Chemical Compatibility

    Hello Group I can find much data on the compatibility of pumped product with Silicon Carbides (Sintered or Reaction Bonded) and Tungsten Carbide (Nickel or Cobalt bound) and the pH ranges of each. I'm having trouble sourcing similar data for 'Carbon' Do resin and antimony carbons have pH...
  2. Milkboy

    Pumping a fluid that is under vacuum?

    Many many thanks for your thoughts on this. Much appreciated M - Milkboy
  3. Milkboy

    Pumping a fluid that is under vacuum?

    Hello group Im looking a repeat seal problem where the shaft sleeve has contacted with the bore of the seal plate. The contact area is at about "2 oclock" So it seems the shaft has move up and over a touch. I have been told that the pumps operate at vacuum. This is where Im getting a bit lost...
  4. Milkboy

    Sealing Brine at 80¦C (176¦F)

    Hello there Group Im looking for advice, suggestions, URLs on material of contruction selection for a pump and mechanical seal which will see Brine (25% w/w) at 80°C (176°F) I have a rule of thumb in my head that says >30°C (86°F) on seawater then Titanium is used. However, I dont know where I...
  5. Milkboy

    Cartridge Seal and Seal System (pot) to ATEX

    Hey group I'm trying to nail down the application of ATEX to mechanical seal so I would appreciate some thoughts. Cartridge Seal on pump in Zone 1 Plan 53 Thermosyphon Seal system Now, to comply with ATEX I have heard much conflicting information. Source W says to monitor the fluid in the...
  6. Milkboy

    Fines in the Barrier System

    Hey Group I have a plan 54 system using 'reclaimed' condensate Temp is <40°C so we have seen no trouble there The question is, it is thought the condensate could have solid/fines in it so a 12 micron filter is used on each system to protect the seal barrier seeing any solids. These filters...
  7. Milkboy

    Sealing Condensate / Condensate Barrier

    Hey Group As I understand it hot water / condensate has a low lubricity and therefore we usually see Carbon v SiC faces in a Mechanical seal. Now then, if you were to use cooled 'recliamed' condensate and a barrier fluid and was sealing against a product which required SiC v SiC, would a...
  8. Milkboy

    High temperature inert barrier seal fluid / lubricant

    Maybe one of the Royal Purple grades would do this job? http://www.royal-purple.net/html/product_summary.html - Milkboy
  9. Milkboy

    Sintered v Reaction (SiC Seal Faces)

    Hey group I'm looking for the lowdown on Sintered and Reaction Bonded SiC Mechanical Seal Faces. Typical Performance differences (temp, pressure, resistance to chemicals etc, strength) Ballpark cost comparisons Can one be shrink fitted and the other not??? Any advice or URLs appreciated...
  10. Milkboy

    Boiler Feed Pump and a Worn Out Seal Face

    Hello Group I have got a cartridge seal from a boiler feed application. 356°F (180°C) at 246 Psi (17 BarG) with a cooled chamber and the seal also has a cooled seat. What I have is an Antimony impregnated Carbon versus a Sintered Silcon Carbide equiped mechanical seal. The Carbon face has...
  11. Milkboy

    L10 Bearing Life and Mech Seals

    Thanks for your responces guys Much appreciated M - Milkboy
  12. Milkboy

    L10 Bearing Life and Mech Seals

    Could you expand on that Mike? Ive got a guy asking for the life expectancy of a seals and he expect the manf. to have data similar to L10 Its just not done, but Im stumbling to find the words to explain why its not done for seals and it is for bearings. I can see his point. Take a Type 1...
  13. Milkboy

    L10 Bearing Life and Mech Seals

    Hey Group Bearing manfs have L10 for bearings Why would mech seal manfs not do the same? TIA - Milkboy
  14. Milkboy

    Boiler Feed Pump

    Hey there Group In boiler feed apps the metal of the mech seal often get a red/brown coating on it. Is this Ferrite? Im looking for info on the source of the ferrite in these apps and how it can be dealt with (mag filters? and the like) Is the ferrite suspended in the water or is it...
  15. Milkboy

    Safety Integrity Level of Mech Seals?

    Do Safety Integrity Levels apply to mech seals ? AFAIK it usually electro, instruments etc Unless someone can advise me differently Thanks - Milkboy
  16. Milkboy

    Tweedy Bread Mixer Seal

    Hi group Bread Mixer seal 80mm shaft SiC v Rulon Faces FDA Viton Component Pusher Type Any experience anyone. Is it an 'off the shelf' seal made by one of the majors then supplied by Tweedy Tweedy can seal to help me as I have no serial number for the machine as it was damaged long ago...
  17. Milkboy

    Seal Faces and Scale

    Theres a school of though that says that scaling / grit / etc would become embedded in the soft carbon and grind away at the SiC. Would you then say this is not the case with CaCo3 scale? Is calcium cabonate scale or similar therefore softer than C faces? Shaft is 4" ! I take onboard your...
  18. Milkboy

    Seal Faces and Scale

    Still await full water analysis but its not listed as being "Hard Water", I think it just has a lot of CaCo3 in there. Temp is 68 to 86 deg F I was hoping use C v SiC as I guess this would run cooler as the C had good lube properties, and there is a chance of dry running / partial dry running...
  19. Milkboy

    Seal Faces and Scale

    Is there any recommended (or personal) limits, say in mg/l, of Total Dissolved Solids where you would switch from Carbon face to Hard face? - Milkboy
  20. Milkboy

    Seal Faces and Scale

    Hey Group If you are sealing a fluid with a quantity of disolved solids and the Calcium Carbonate has a tendancy to scale, would you expect scale to form on the actual sliding area of the seal faces OR Is hang up more of concern when it comes to scaling? TIA - Milkboy

Part and Inventory Search

Back
Top