Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. resjsu

    Force Needed for Lid to Tip Assembly

    I had a few in the attached PDF but several questions for each scenario, can you explain a little further? We have 2 pieces of metal colliding, I dont know how else to get a good measure of the impact time or stopping distance. Like I said we recorded on video and watch in slow motion and...
  2. resjsu

    Force Needed for Lid to Tip Assembly

    rb1957, In the included PDF I have a value ( I dont know if its right) for the calculated Force and the impulse; aside from these being correct or not was the method I used not correct? We do not have scales available but if working this by hand does not produce anything useful I will have to...
  3. resjsu

    Force Needed for Lid to Tip Assembly

    What does the lid impact? Without knowing this, I don't believe a meaningful answer can be obtained. The lid impacts a stop connected to the base, I left it out of the simplified model. When the lid reaches the max opening 90 degrees, for simplicity, I am assuming it hits the hard stop and...
  4. resjsu

    Force Needed for Lid to Tip Assembly

    1) For my "Case 2", the force needed to tip the container can be calculated using statics. You are talking about summing moments correct? Again, this is if the force of the lid is constant but in this scenario the force is not constant, it is an impulse. 4) Knowing the deceleration (Step 3)...
  5. resjsu

    Force Needed for Lid to Tip Assembly

    SlideRuleEra, Thank you for the response but I am not quite understanding your comment. I may have used the wrong language but my thought process was as follows: I cannot measure the acceleration of the lid as easy as I can the angular velocity; we achieved this through slow motion video Once...
  6. resjsu

    Force Needed for Lid to Tip Assembly

    Hello, I read few threads about tipping hazards on here and have used some of the info to attempt a solution. I have attached a PDF with all of the info and work. To summarize, we have a container that has a heavy lid and I want to determine if and at what opening velocity the lid will tip the...
  7. resjsu

    Multiple Bore Features as a Single Datum

    Belanger, Thank you, it helped reading some varying points of view. However, it didnt do a whole lot in the way of clarifying too much. I did key in to your response regarding taking measurements from basic dimensions relative to the datum. So, in my case after checking each hole individually...
  8. resjsu

    Multiple Bore Features as a Single Datum

    Ok, so assuming MMB how do you find the "geometric center" of a 10 hole pattern? I see the example in the ASME14.5 but they are using 4 holes which is a little more intuitive. If I do not have to find the center, how then do I use this 10 hole pattern as a datum used to check other features? I...
  9. resjsu

    Multiple Bore Features as a Single Datum

    Pmarc, This is a redlined print that the customer is considering. On our side, we are trying to determine if we would be able to check the part if they made these changes. For educational sake could you provide basic info on how RMB or MMB would affect the datum scheme?
  10. resjsu

    Multiple Bore Features as a Single Datum

    Mkcski, Yes, all 10 axis are parallel to each other.
  11. resjsu

    Multiple Bore Features as a Single Datum

    Pmarc, I apologize. Both of the 4 and 3 holes was just an example to get a better understanding.. In either case my dilemma is the same, I cannot think of how to check multiple holes being used as a single datum on a cmm/faro. See attached PDF, it is a redline from our customer who wants to make...
  12. resjsu

    Multiple Bore Features as a Single Datum

    Pmarc, Excellent, I found it in the spec. So it is obviously allowed now in terms of measuring with faro/cmm since there is no pattern callout is it just treated as if the holes were individual? In other words if I have a 3 hole pattern that the customer is calling collectively datum -B-, when I...
  13. resjsu

    Multiple Bore Features as a Single Datum

    Hello, So as topic states, 1 of our customer drawings has 4 holes called out as a single datum. Nothing I have read in the ASMEY14.5 standard (I could be missing it) really touches on this issue. I have basic questions; is it allowed? How would you take dimensions using a datum composed of...
  14. resjsu

    In ref to this post: Bubble Drawings

    thread286-339304 Just as an FYI, I found this website sometime ago. Hope it helps guys! www.bubbleexpert.com
  15. resjsu

    Create Bubble or Balloon Drawings

    Hello, I remember reading a few posts on here about people looking for a simple program to bubble PDF documents and image files. I was in this position myself and was forced to buy InspectionXpert even though my office would not be using most of the tools available in InspectionXpert; we still...
  16. resjsu

    Another Unknown GD&T Symbol - Enclosed ' V '

    hydtools: I agree. I cant explain the reasoning I just no what happens everytime we ask to speak with the customer tp clarify issues. 3DDave & tbuelna: These are great ideas, it never occured to me it may just be a font issue but it makes sense as we too have seen some weird font conversions...
  17. resjsu

    Another Unknown GD&T Symbol - Enclosed ' V '

    RoleMec: I will definitely look into your ideas. As far as it being a variation form a previous drawing, the drawing has a standard revision block with dates/changes made etc. The current revision level is 'J'. There are not notes on the titleblock referring to this circled 'V'. Yes, for the...
  18. resjsu

    Another Unknown GD&T Symbol - Enclosed ' V '

    Ctopher: For the most part, the rest of the drawing is defined through GD&T standards. KENAT: There are no other notes on the drawing regarding internal drawing standards. Virtual condition is a good guess, I will look a little more clsoer at it but my gut tells me it is not for virtual...
  19. resjsu

    Another Unknown GD&T Symbol - Enclosed ' V '

    Hello All, I have come across another symbol I am not familiar with and have not been able to find in any GD&T book. I am starting to lean towards "typo" but the drawing comes from a very prominent Automotive customer and I feel like they wouldnt make mistakes too often. So before I put my foot...
  20. resjsu

    Unknown Drawing Symbol

    Lots of good information and I appreciate all insight. Can someone translate what the symbol and value mean into a sentence?

Part and Inventory Search

Back
Top