Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. Wyzzard

    ASME Non Code Vessel repairs

    To The Orburator, I don't think you were totally accurate with your response. The ASME boiler & Pressure vessel code does not actually REQUIRE an R stamp for repairs. The ASME BPV Code is for new construction, not in service or repair work (with a small few exceptions, i.e. Section XII). It is...
  2. Wyzzard

    How to Report ASME BPVC Fabricators that are supplying vessels that do not meet Code?

    Send a letter , again, to ASME, specifically addressing the allegations. Address it to the Director of Conformity Assessment. Also copy the National Board. Address that one to the Executive Director. I will be shocked if they do not respond to you. It is their job to look into ALL allegations.
  3. Wyzzard

    ASME Authorized Inspector NB commission number verification

    You an check directly with the National Board. They are in Columbus, OH 1066 Crupper Ave, Columbus, OH 614-888-8320 They will help you.
  4. Wyzzard

    NBIC Commissioned Inspectors training- Course materials

    You can check directly with National Board of Boiler and Pressure Vessel Inspectors. They are located in Columbus, OH.. They are the organization that develop and conduct the AI exam. 1066 Crupper Ave, Columbus, OH 614-888-8320
  5. Wyzzard

    New Pressure Vessel and not put into service to be repaired

    I agree with WeldStan. Use the NBIC. This is probably the most accepted repair code worldwide, for boilers and pressure vessels.
  6. Wyzzard

    Repairs ASME Sect 1/NBIC/Temper Bead P4-P5A material

    To use the revise alternative welding method that metengr stated, if you cannot wait until the 2019 edition of the NBIC is published, then check with your local State Chief boiler Inspector. He may allow use of this revised method before publication. You just won't be able to R stamp the work.
  7. Wyzzard

    boiler tundish

    Thanks JStephen. I did google it. Hence the question here. The internet definition indicates that it is like a conical tube or a funnel to fill a pipe for drainage purposes. My drawing has numerous drain lines. Some go to "tundish" others just say "drain". But I think they all end up in...
  8. Wyzzard

    boiler tundish

    I am reviewing a P&ID for heat recovery boiler, and there is a term used I am not familiar with. Tundish. Can any help with this term?
  9. Wyzzard

    NBIC Applicable to Building Services Steam Piping ?

    After reading this chain of posts I can see why you were (are) frustrated. The short answer to your question is that NBEP is outside the scope of NJ boiler law. So you do (or did) not need to have the repair performed to the NBIC. I woill add another bit of info for you. NJ has their own R...
  10. Wyzzard

    ASME Sect 1, PW-54.2

    This has been interpreted already by the ASME Committee. I-82-04. Interpretation Number: I-82-04 Question(s) and Reply(ies): Question (1): When performing a hydrostatic test on a vessel of welded construction per PG-99.2, is any leakage through the weld(s) permitted? Reply (1): No (see...
  11. Wyzzard

    Changing ASME Authorized Inspector

    Scott, I am curious. How did this issue get resolved? Was the data report evrer signed?
  12. Wyzzard

    Texas Boiler Code

    Yes it is a boiler under the State of Texas boiler law.

Part and Inventory Search

Back
Top