Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. portliner

    boundary conditions for sphere in rotation and translation

    Hi, as a understand the model consists of solid elements in the plate and the sphere as well. Solid elements have only 3 DOFs(translations) x, y and z. NO ROTATIONS exists for solid elements! The plate should only be fixed by specifying theses DOFs to zero. Specfying a predefined rotation of the...
  2. portliner

    boundary conditions for sphere in rotation and translation

    Set the BC to zero in desired directions for the plate, do it in the "initial state" and the let the BCs propagate to the subsquemt STEPs. Choose "edge" geometry to apply BC on.
  3. portliner

    boundary conditions for sphere in rotation and translation

    If you build the model in the CAE, you apply the BCs in Load > BC.
  4. portliner

    Nodal forces in local coordinate system

    You can transform results between different c-systems in the Viewer. Results > options I think... try
  5. portliner

    Sub-Model at a specified location of Global model?

    You can draw the sub-model in the patrt-module regardless of the coordinates directions. Then create a coord-system in the part positioned to express the desirde coordinate-values for the corners.
  6. portliner

    Abaqus Heat Transfer on an aluminium cylinder

    Yes, you can give a formula for the local heat transfer coefficient by using the subroutine FILM. In this outine the local temperature of the current node in the call is available for you.
  7. portliner

    Automatic Stabilization

    It creates a non-real viscous stiffness to avoid zero stiffness. The more you increas the factor the more stiffness and better convergence but less realistic solution.
  8. portliner

    Cross-section forces

    Not in the "initial", create a dummy STEP type STATIC as the first STEP.
  9. portliner

    Cross-section forces

    Create a BOLT pre-tension section in a first STEP, use "fix bolt length". Create a time-history of the sectional forces for the pre-tension section. Apply the whatever loads in the next STEP(s).
  10. portliner

    Submodel help.

    Hello Simon012, I have no experience of changing material properties. However, I believe You should change the *Initial conditions of the relevant parts in the sub-model as You did in the global-model. As I understand, your sub-model extends into regions where you change the material...
  11. portliner

    No frames available for step

    ... check if the job completed successfully in the .sta-file
  12. portliner

    Submodel help.

    ...for its use as governer of the SUB model. 1. Create a cell by partition in the GLOBAL model. Use this cell as the SUB model later on. 2. Create *Nset on the interfaces between the cell and the rest of the GLOBAL model. 3. Print displacements for the nodes in this *Nset to the, I think...
  13. portliner

    Preload Bolt

    ...bolt nessescarly. The model consist, as I believe of the bolt and at least one other structure, stretching between the bolt-head and its thread. *Contact or *Tie must be defined between the contact surfaces between the bolt-head and its mating structure The same must be defined for the...
  14. portliner

    Preload Bolt

    The pre-tension section divides the bolt into two parts. The force or distance between the two surfaces, created when defining the "cut" is governed by either a prescribed force or a prescribed distance. If a prescribed force is to be applied, the both parts of the bolt are NOT allowed to be free.
  15. portliner

    Find model weight

    You can start a modal STEP and get the total mass in the .DAT file
  16. portliner

    Preload Bolt

    You can not apply a force if only one end is fixed , no stiffness
  17. portliner

    Load control Vs. displacement control

    You can apply prescribed displacement(s), increasing them by small time-increments. Monitor the resulting reaktion forces and evaluate the solution when the forces reach the desired value(s).
  18. portliner

    Nodes temperature in INP file

    In general ABAQUS refers to a node, element or set in an instance by specifying name-of-assemble.name-of-instance.ID-of object
  19. portliner

    Nodes temperature in INP file

    My suggestion is to apply the individual temperatures on each node in CAE
  20. portliner

    submodelling techique- help

    Caution about loads, You should applly loads to the submodel ONLY if the load acts on the subregion. Fpr example a presure load on a certain surface of the global model should NOT be applied to the sub-model IF this sub-model does NOT extend right up to this loaded surface. The gravity applies...

Part and Inventory Search

Back
Top