Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

Register Log in
  • Congratulations waross on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Birdsmouth I-Joist Cut

GaStruct

GaStruct

Structural
May 20, 2024
81
Saw this gem on site. Can anyone think of a fix that doesn't involve ripping it out and redoing it?

I am thinking maybe blocking between the studs and driving screws through the bottom flange into the blocking?

Boise allows birdsmouth but the bottom flange must be supported.
 

Attachments

  • IMG_3642.JPEG
    IMG_3642.JPEG
    1.2 MB · Views: 64
Replies continue below

Recommended for you

Sort by date Sort by votes
top flange hangers with up sloped seats add blocking between joists as needed to build up for the hanger depth. Will need to detail the blocking attachments for stability.
 
Upvote 0 Downvote
You could provide a dropped ledger with beveled top bearing surface. You'll probably want to block the webs in addition to this.
 
Upvote 1 Downvote
Celt83 said:
top flange hangers with up sloped seats add blocking between joists as needed to build up for the hanger depth. Will need to detail the blocking attachments for stability.
Click to expand...
Interesting idea, I will look into it. Although, the nails in the web would be doing the work - not sure if that satisfies Boise's intent?

atrizzy said:
You could provide a dropped ledger with beveled top bearing surface. You'll probably want to block the webs in addition to this.
Click to expand...
I thought about this too. It would make the wall look weird when finished though.

DaveAtkins said:
I would share the photo with Boise and get their recommendation.
Click to expand...
agreed.
 
Upvote 0 Downvote
GaStruct said:
I never spec them for rafters but apparently the lumber supplier couldn't get 22' long 2x??
Click to expand...
Around here most places will stock 2x's up to 20 ft. Anything over that and they'll have to order them. Also, 20ft+ long 2x's are rarely straight and guys prefer engineered lumber so my guess is that this install is a combination of those two things.
 
Upvote 0 Downvote
I talked to 84 Lumber last month - our yard stocks 24' 2x10s and 2x12s, at least. Didn't ask about anything smaller.
 
Upvote 0 Downvote
Tough one. With the roof already in place, it will be tough to argue that there is not significant DL travelling through that undesirable load path no matter what you do.

Conceptually, you might:

1) Get rid of the plywood.

2) Install some 2X outlooker things that get moment connected to the joist webs and bypass the first bit of the joists.

3) Maybe even cut off the bit of the joist that would be inclined to crack off.

I could see this being pretty tough to do spatially though. Not much room to work in between the joists.
 
Upvote 0 Downvote
You must log in or register to reply here.

Similar threads

Bammer25
  • Question
I joist to steel beam
Replies
14
Views
5K
Eng16080
Eng16080
XR250
  • Question
I-Joist Rafter Connection
Replies
15
Views
3K
ANE91
ANE91
ingenii
  • Question
Joist seat forces in Multiple Span Joist Construction 1
Replies
11
Views
3K
ingenii
ingenii
R
  • Question
Existing Steel Joist Identity
Replies
3
Views
267
Ron247
Ron247
dgengineering
  • Locked
  • Question
Truss Cut 1
Replies
19
Views
4K
BAretired
BAretired

Part and Inventory Search

Sponsor

Back
Top Bottom