Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by rmorgan890

  1. rmorgan890

    Embedded Sketch Question

    Thanks for your help!!
  2. rmorgan890

    Embedded Sketch Question

    Yep, that's it. Using Rapid Dimension, I just created a sketch dimension and under "Driving" i checked "Expression", and it worked. Thanks, Is there any down side to making Sketch Dimensions Expressions, other that maybe a few extra clicks?
  3. rmorgan890

    Embedded Sketch Question

    Both. In the old file, i noticed the existing features with internal/embedded sketches this still works, but if i create new feature it doesn't. As a side note, I think "internal sketch" is probably the correct term. Not "imbedded sketch." My bad.
  4. rmorgan890

    Embedded Sketch Question

    It's not dependent on other features. For example, the problem is the same for a model that contains just one extrusion, as well as a model with fifty features.
  5. rmorgan890

    Embedded Sketch Question

    Just moved to NX 1953 from NX 12. Previously, I was able to right mouse click on features with embedded sketches and pick Edit Parameters and the sketch dimensions would appear without going into the sketch. I no longer see this in NX 1953. Is this functionality gone? Thank you,
  6. rmorgan890

    Leader termination point

    Made no difference in this case. Thanks.
  7. rmorgan890

    Points and curves won't appear in drawing views.

    Updated the views first thing. Didn't help. I probably should have mentioned that. Sorry.
  8. rmorgan890

    Points and curves won't appear in drawing views.

    Using NX9 I created a point and a line (using Basic Curves)on the modeling side of my drawing Dataset. When I flip to the drawing side, the point and line do not appear in any existing drawing views. This is not Layer or View Dependent issue. I've seen this before. This is a...
  9. rmorgan890

    Leader termination point

    Using NX9 Sometimes when adding a Note, Finish Symbol, etc to a drawing, NX will allow me to select anywhere on a Dimension Extension Line for my leader termination point (my preference). Other times, when I try to select a Dimension Extension Line for my leader termination point, it snaps to...
  10. rmorgan890

    Load Options (All components vs Structure only)

    Cowski, I understand this, but when I open the assembly in the Assembly Navigator using "STRUCTURE ONLY" I'm getting different results. Thanks
  11. rmorgan890

    Load Options (All components vs Structure only)

    I'm using NX 9. What is the difference between opening an assembly with Load Options set to "All COMPONENTS" vs "STRUCTURE ONLY" and then opening the entire assembly in the ASSEMBLY NAVIGATOR? Thanks
  12. rmorgan890

    Deform User Expression

    Using NX 10. I create a model with a User Defined Expression which is used by a three different sketches. It works pretty good. If I change the value of the Expression, the model updates. Is there an option in Define Deformable Part, to made the User Defined Expressions Deformable? In the...
  13. rmorgan890

    Associated sketches

    Ya,but when I change the second sketch the third changes.
  14. rmorgan890

    Associated sketches

    For the two subtractions, I just selected the top face of the first extruded rectangle to create sketches.
  15. rmorgan890

    Associated sketches

    Using NX10. I have a very simple model with three features. The first is a simple extruded rectangle with an embedded sketch. The other two features are simple extruded shapes subtracted from the first. The subtracted excursions have nothing to do with each other, but for some reason the...
See more

Part and Inventory Search

Back
Top