Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by Munnichs

  1. Munnichs

    Can't select '3D input devices' under 'Preferences'in NX 6

    Hello, Ihave some issues with the zoom about attention point. For this I wanted to look under preferences, 3D input devices. But the problem is that 3D input devices is grey, and so I can't select, while my colleagues can. Does anybody know what causes this? Kind regard, Roy Munnichs.
  2. Munnichs

    When zooming out in Drafting, lines disappear

    John, The reason I started this thread in the first place is that, despite several phonecalls to the Dutch Siemens helpdesk, I didn't get a any information about this issue at all ! If they told me that it was a known issue then I didn't have to bother you with this. Since in the other thread...
  3. Munnichs

    When zooming out in Drafting, lines disappear

    I have a problem in Drafting with NX 6.0.5. When you for example zoom in to a view, add some balloons, and then zoom out, not all lines are visible (they disappear). After refresh/update, the lines will be visible again. See attached pictures. It started happening when we installed MP1. Does...
  4. Munnichs

    Drafting in NX 7.5 doesn't refresh.

    I have the same problem but we are working with NX 6.0.5. When you for example zoom in to a view, add some balloons, and then zoom out, not all lines are visible. After refresh/update, the lines will be visible again. It started happening when we installed MP1. Does anyone else has this problem...
  5. Munnichs

    Does NX5 run under Windows 2000 ???

    Hello, We have a Dell PC with Windows 2000 on it. We currently use NX4 and it runs good on this system. However we want to upgrade to NX5, but it is not supported by UGS. My question is : has anyone tried to install NX5 on a Windows 2000 system? And does it run good, because the PC that we...
  6. Munnichs

    Problems with printing in NX3

    Rghay, We cannot plot because our printer/plotters are not supported (HP Designjet 100 and HP Business inkjet 1100) for plotting in NX. Mustangman2001, We also have the same problems when making PDF's. Since NX 3.0.3.2 mp4 there has been a change in printing in NX, which might explain that...
  7. Munnichs

    Problems with printing in NX3

    Hello, We are working with NX3 and having promblems with printing. We have a HP Designjet 100 printer/plotter, which supports PCL3. But since NX3 (and also NX4) do not support this language, the prints are awfull. I called GTAC about it and they said, that they cannot solve the issue. But...
  8. Munnichs

    How to create a surface by boundary in NX3

    Thanks, this is exacly what I want. But then there is another issue: why can't find this option in the 'surface' toolbar? Kind regards, Roy Munnichs.
  9. Munnichs

    How to create a surface by boundary in NX3

    Does anybody know how to (easy and fast create) a rectangular surface out of a set of curves? In I-deas there was this option 'surface by boundary'. I there a similar command in Nx3, except 'Through curves'? Kind regards, Roy Munnichs
  10. Munnichs

    How to edit toolbar buttons?

    The button I'm looking for is 'Surface finish symbol'. I can't find it any tbr-file ! Regards, Roy.
  11. Munnichs

    How to edit toolbar buttons?

    Does anybody know how to edit toolbar buttons? I can't find any info in the help documentation. Regards, Roy Munnichs.
  12. Munnichs

    Problem creating a rectangular array

    It works. Many thanx
  13. Munnichs

    Problem creating a rectangular array

    I have a problem creating a rectangular array. When I make a block (100x100x100 mm), and then make a array of it (2 itemss in X, spacing 300), I get an error 'Tool body completely outside target body'. But this is exactly what I want. Is there a different way to create such an array? Regard...
  14. Munnichs

    How to measure radius of cilinder?

    Thanx.
  15. Munnichs

    How to measure perpendical distance between point and face in NX3

    Thanx
See more

Part and Inventory Search

Back
Top