Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by MohammadB84

  1. MohammadB84

    Video and KVM extenders with Cat6A

    Protocol difference was brought up by the manufacturer tech support. But as you mentioned, if the cat6a has a larger phase difference then that could be a problem?
  2. MohammadB84

    Video and KVM extenders with Cat6A

    Thank you John! Cat6A does have a better performance however, that's mainly concerned with ethernet, when it comes to video signal which has a different communication protocol that can't necessarily be concluded and the latency caused by different pairs of wire could cause color disruption in...
  3. MohammadB84

    Video and KVM extenders with Cat6A

    Hi, For a project in my hospital I need to use several video and KVM splitter/extenders for remote displays. Most of the products that I find are designed for Cat5e or Cat6 cables. The problem is that all the infrastructure in our new facility is Cat6A cable. I'm wondering if anyone has had any...
  4. MohammadB84

    Spare Network Switches

    Hi, My question is more of an IT infrastructure one but since I couldn't find a more relevant forum I thought I post it here. So here is it is: I am a clinical engineer in a Hospital and currently we are designing new Biomed Data closets (Similar to tel/data closets) for a new building. These...
  5. MohammadB84

    Fault Tree Analysis

    Hi, I was wondering if anyone could help me out with a FT analysis that I am currently conducting. My question is that in the tree if I have the basic events Failure Rates(#failure/10^6 hrs) instead of the Failure probability and that is the only information I have from my component(basic...
  6. MohammadB84

    COSMOSMOTION 2008

    Hi, Just wondering if anyone has any idea where I can find some usefull (free) tutorials on COSMOSMOTION 2008. I need to use it to simulate dynamics of a device I'm testing. One more question now that I'm making this thread, again in COSMOSMOTION, in the rotary motors there are 4 or 5 options...
  7. MohammadB84

    COSMOSMOTION 2008

    Hi, Just wondering if anyone has any idea where I can find some usefull (free) tutorials on COSMOSMOTION 2008. I need to use it to simulate dynamics of a device I'm testing. One more question now that I'm making this thread, again in COSMOSMOTION, in the rotary motors there are 4 or 5 options...
  8. MohammadB84

    How do I calculate the Max bending force for a metal plate?

    I am designing the required safety tests for the lift according to CSA. The tests are not going be done on people, we are using sandbags as weights. There are so many tests to be passed before any human trial.
  9. MohammadB84

    How do I calculate the Max bending force for a metal plate?

    Thank you 40818 and Gymmeh for the book name!
  10. MohammadB84

    How do I calculate the Max bending force for a metal plate?

    Hi KENAT, I have all the properties of my metal such as tensile strength and so on. The plate is fully supported at both ends and it has an angle of 10 degs. Can you name one those textbooks please? Thanks, Mohammad
  11. MohammadB84

    How do I calculate the Max bending force for a metal plate?

    Hi, I am in the process of testing a very heavy mechanical patient lift. The lift has to be placed on the surface of a sloped metal plate. The weight of my lift(load) is known (~ 1040 kg). The metal plate that i will be using is a carbon steel plate with the dimensions of 96"X60", but I am not...
See more

Part and Inventory Search

Back
Top