Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by mectub

  1. mectub

    Pipe Deflection using CAESAR

    Oil and gas Industry (PDVSA Venezuela). I am referring to data at midpoint between supports.
  2. mectub

    Pipe Deflection using CAESAR

    You are right that is what I mean, there is a guide for piping supports used by my company establishing 15 mm max for pipe diam. <24", that is my max deflection. As well is included a top of 50% of basic allowable stress at operation temperature for bending stress limit.
  3. mectub

    Help - thickness of pipe

    Becouse of the threaded join must be sch 80 considerin thickness reduction a thread.
  4. mectub

    Pipe Deflection using CAESAR

    Hi everyone, i know that if i want to have the deflection number, i must use a node at interest point, but when i'm checking a model a maximum deflection is one of my goal, so is there a way in CAESAR to set a max deflection or max bending stress in order to get a warning?. What if i want to...
  5. mectub

    B31.3 hydrotest code check

    No, none of them has been specified.
  6. mectub

    B31.3 hydrotest code check

    Hello everyone i'm doing an stress analysis using HYD case.I would like to know why a piping system do code stress check and the other dont. Both using B31.3 and same HP. Thanks for your help
  7. mectub

    HTRI Shell Geometry Output

    Thanks a lot adamp716,that clear my doubts!!
  8. mectub

    HTRI Shell Geometry Output

    Hi, anyone could help to understand the meanning of this part of the output summary given by HTRI software, when it says (Shell geometry) Series 1 and Parallel 2, i think this is i need 1 row of 2 equipment in parallel. How if Series 2 and Parallel 5?
  9. mectub

    Valve TRIM materials

    Thanks, where can i find more info about this issue, i want to learn more on this topic.
  10. mectub

    Valve TRIM materials

    Which code defines TRIM materials, i've been searching and found in API 600 a table with basic trim mateials, this is the right one or there is other. API 6D don't mention it neither ASME B16.34. My valve is a 20" gate type API 6D.
  11. mectub

    Check valve located into piggable portion of a pipeline

    I dont get this,"The question there is why the heck did they try to pig it", would you explain your question please.
  12. mectub

    Check valve located into piggable portion of a pipeline

    my case is ralated with an oilduct it cross a river and B31.4 recommends to use block valve up and downstream the river border to minimize oil to spill and it could be a gate or a check valve, the thing is using check valve could cause the pig to stuck, some one has use one.
  13. mectub

    Check valve located into piggable portion of a pipeline

    ASME B31.4 state as mainline pipelines: all in-line pipeline pipes, fittings, bends, elbows, check valves, and block valves between scraper traps. So it is a good practice to install a check valve (swing check valve)in a pipeline when pigging is required? thanks to all
  14. mectub

    DIFFERENCE ALLOWABLE STRESS BETWEEN PVELITE AND B31.3

    The three give a value for this material, thanks to gr2vessels i solved my doubts, if you are going to design a piping system under B31.3 tablae A-1, pag 144, S will be 23.3 ksi, in other hand for pressure vessels Div 1, Section II, Part D, Table 1A,Pag 18 to 20,line 22, S= 20 ksi those tables...
  15. mectub

    DIFFERENCE ALLOWABLE STRESS BETWEEN PVELITE AND B31.3

    Right! i just figured out, and get to Section II, Part D, Table A1, these and others applay for Div 1, now im going to check out table 5A to see Alloweble Stress aplicable to Div 2
See more

Part and Inventory Search

Back
Top