Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by gutboy17

  1. gutboy17

    Surface normal vector orientation

    Group, I'm currently modeling a fluid storage tank that is under a pressure load. I'm having difficulties getting the applied pressure loads to be applied in the same direction for all of the surfaces. Some of the surfaces have the load vector pointing inwards on the tank and others are point...
  2. gutboy17

    Inventor 2011 not working after updating to Windows 8.1

    Thanks for the great advice mcgyvr. I wish I was a smarter person to figure out how to re-install windows and my CAD software. Which slot does the DVD go in? One step at a time, I just learned how to turn on the mouse.
  3. gutboy17

    Inventor 2011 not working after updating to Windows 8.1

    I updated to Windows 8.1 a few weeks ago. I went to use my Inventor the other day and I get an application error on launch (error 0xc0000142). Anyone else having the same issue? AutoCAD still functions properly.
  4. gutboy17

    USC Online Master of Science Aerospace Engineering Degree

    Can someone recommend this program for an online Masters program in Aerospace. I'm looking at the Aerospace Structures core program. Also, if you have experience with another online program please list that one here as well. Thank you.
  5. gutboy17

    Aircraft Designer Martin Hollman Dies

    A legend in the Gyro and experimental world. I took a couple of his courses and really enjoyed them. You can't beat where he lived (Monterey, CA). God Speed, Martin.
  6. gutboy17

    Fuselage Cutout

    Thanks rb1957 and SparWeb for the info. It helps out a lot. I have all of those references and I'm looking through them for an appropriate substantiation. The sensor does not extend past the OML of the fuselage, so I can't see any aerodynamic loading affects. The sensor will also have no...
  7. gutboy17

    Fuselage Cutout

    Not pressurized. No antenna. It is Part 25 It is a small opening for a sensor that will not be extending into the airstream. No loads are transmitted from the sensor to the opening. I "just" need to show that my opening and the external doubler I'm putting around the opening returns the...
  8. gutboy17

    Fuselage Cutout

    I need some assistance on where I could find an analysis method for cutouts in a fuselage. I need to add a small opening in the side of an Aluminum semi-monocoque fuselage. I'm not cutting any frames or stringers, just the fuselage skin boxed within the frames and stringers. I don't have any...
  9. gutboy17

    Acceleration units

    I'm getting back into the FEM world with a simple structural analysis undergoing acceleration loads. I thought the acceleration units were in inches/sec/sec (32.2"/sec/sec = 1g). However, when I apply the acceleration loads to the model, the freebody resultant loads are a factor of 12 greater...
  10. gutboy17

    Which university has the best aeronautical engineering in USA?

    My vote goes for Cal Poly, San Luis Obispo, CA. Great education experience. Great industry contacts. Great area to spend 4 yrs.
  11. gutboy17

    Wing Box Design

    Is this company willing to fund testing for validation. There are plenty of resources that will test the product that can be used for validating the FEA and the other performed analysis.
  12. gutboy17

    Post Material Removal of Shot Peened Surface

    Condition: I have a 7075-T6 part that has been shot peened. However, a local surface feature of the part needs to have .050" of material removed for assembly fit. I don't know the shot peen process (i.e. type, intensity, etc.) of the current part needing the dimensional work. My question is...
  13. gutboy17

    Rivet Bearing

    My question is concerning the method of calculating rivet bearing loads on the parent material for a countersunk rivet. First off, is it usually calculated or does the countersink make it not as critical as shear load? How is the contact area calculated for a machined, dimple, or double dimple...
  14. gutboy17

    IGES ouput options

    I'm not a user of CATIA, but I'm requiring another company to supply me with an IGES output of a model that they developed for the purpose of CFD analysis. Is is possible for CATIA (all versions) to format the conditions of an IGES output so that the output is of NURBS curves (entity 126) and...
  15. gutboy17

    AN, MS and NAS standard fastener and hardware catalog

    Just another quick plug for a useful product. www.sacskyranch.com sells a CD with a lot of useful info in an interactive window format. The CD is called the Mechanic's Toolbox and was developed for the aircraft mechanic in mind, but it does come in handy for engineering design.

Part and Inventory Search