Graybeard:
One last comment:
In your risk analysis between the two types of construction, some factor should be applied for catastrophic failure. I'm assuming if the rubber lining fails, the steel structure will not last very long and provide the potential for catastrophic failure, perhaps in...
Graybeard:
I myself haven't heard of rubber lined carbon steel being used in NaOCl service. The eight years service life is quite respectable. All you can expect from straight fiberglass is about 7-10 years if its built properly, as I mentioned above. The cost for this type of construction...
Panteo,
The tanks are large, but could a vacuum condition ever exist? Vacuum rated flat bottoms can be expensive in such large tanks. For example, if the PVRV is rated for -8" WC, then maybe the drain was located 8" (or equivalent given SG of HNO3) above bottom so it won't...
What kind of equipment are you looking for? The kind of equipment required could help in determing the right materials of construction. i.e. are elastomeric seals required? Is the equipment even rotating or is it static, like a storage tank, etc. Is it short term exposure or long term?
Also...
The Carpenter 20 would be used in a 6000 gallon storage tank. 96-98% H2SO4 is received by truck. Because the tank is vented to atmosphere, the moisture pickup drops the concentration to approximately 93% (+/- a few %) before the next load. A nitrogen pad to keep the moisture out is probably a...
Has 100% FRP construction been considered? There are a few companies that can build FRP tanks as large as you require. Resistance to organics is of primary concern, but a novalac epoxy vinyl ester resin (i.e. DEREKANE 470) should suffice.
For manufacturers to build this type of equipment, see...
Are there any drawbacks to using Carpenter 20 in 93-98% sulfuric acid service? Is Carpenter 20 the same as Alloy 20? The temperature is ambient (-30 to 110F).
Thanks
I have experience with both companies and both are very good.
Try:
Creative Pultrusions Inc.
214 Industrial Ln.
PO Box 6
Alum Bank, PA 15521 USA
Tel: (814) 839-4186 Fax: (814) 839-4276
Business: Pultruded tubes and structures
OR:
DFI Pultruded Composites Inc.
1600 Dolwick Dr.
Erlanger...
I recommend getting a copy of the latest ASME RTP-1 standard, which will answer all of your questions about fiberglass construction for vessels rated from full vacuum up to 15 psig.
http://members.asme.org/catalog/CategoryView.cfm?Category=CS&Designator=RTP
A lot of chemical companies (such as...
Hangglide,
My company has been doing infusion for several years now using the SCRIMP process. We have found this process very effective for certain applications, however, we've begun recently to use the CARTM process. With the CARTM process, we've infused panels as thick as 4" and...
Flouropolymer (Kynar, Halar, or Teflon) lined fiberglass (dual-laminate) can be used for the column, feed tank, and product tanks and would be more economical than Hastelloy. In addition, PTFE internals can be manufactured to hold up to the constituents. Heat transfer becomes a bit of a...
DougW: more information to digest:
Please see following links for corrosion recommendations of vinyl ester resins used in fiberglass constructions:
Accessed through (www.hetron.com):
http://www.ashchem.com/ascc/compoly/cg.asp?nCountNumber=281&alpha=S&is_header=N
I would recommend Hetron 922...
I would go with the fiberglass option using a Section X, Class 2 code stamp (if you're in one of the 28 states that requires a Section X stamp on pressure vessels). Even if you're not in one of the states that requires it, I would still go with a code stamp if the vessel was in my plant... The...
I'm not sure about metallics, but we're helping out a phos acid plant right now who uses lots of Teflon-FEP lined fiberglass pipes and tanks. This material seems to be working out exceptionally well for them. Perhaps the wetted surfaces of your pump can be coated with Teflon FEP or PFA.
Greg...
