Recent content by bongoman

Hi All, I have a question on creating new 5 axis table-table posts in postbuilder. If I create a new 5-axis table-table post with library Fanuc control and another with the library Heidenhain control and set up machine XYZAC the same in both I get different X and Y moves but the same A and C...

Hi All, I keep getting this information window warning message when I switch between modeling and manufacturing or when I start NX new and call up this part file. Anyone know how to stop or turn off this warning as there is NO problem with the toolpath and I have many of these blends programmed...

Hi Michal, I ended up uninstalling and re-installing NX11 with "typical" as well but did not use "customize" the 1st time. It is working now. Contacted GTAC but they could not help me. Regards, Rick Win7 64 bit w/NX10.0.3.5 MP14 and NX11.0.1.11 MP1 Vericut 8.0

Thanks for the quick reply John. Good to hear from you. Unfortunately that didn't work so I will contact GTAC. Win7 64 bit w/NX9.0.3.4 MP9 and NX10.0.3 Vericut 7.4

When I try to use split body in NX11.0.1.11 MP1 I get an error message "A deleted or invalid class id was used". Then nothing. Anyone run across this one? So far everything else seems OK. Rick D Win7 64 bit w/NX9.0.3.4 MP9 and NX10.0.3 Vericut 7.4

Hi John, This is how I have it set and NO UDE's active. Rick D Win7 64 bit w/NX9.0.3.4 MP9 and NX10.0.3 Vericut 7.4

I have a postprocessor set up for inverse time and occasionally it puts out a G94 with an angle in the line (see example code below). I thought if there is an angle in the move it should be G93. Anyone know if this is correct behavior and if not how to stop the post from putting a G94 out on a...

Hi Cowski, Got this to work. A bit messy but working Rick D Option Strict Off Imports System Imports System.Collections.Generic Imports NXOpen Imports NXOpen.UF Module Module3 Public selFace As Face Public cursor As Point3d Dim theSession As Session =...

Thanks Cowski I will give it a try Rick D Win7 64 bit w/NX9.0.3.4 MP9 and NX10.0.3 Vericut 7.4

Hi Cowski, Yes I need to select a cylindrical face (hole). Thanks, Rick D Win7 64 bit w/NX9.0.3.4 MP9 and NX10.0.3 Vericut 7.4

Thanks Cowski, Haven't done a journal in a while and think I forgot that they need a selection method and simple dialog from within VB. Now if I can only get the selection to work. Rick D Win7 64 bit w/NX9.0.3.4 MP9 and NX10.0.3 Vericut 7.4

Hi All, I'm trying to record a journal to display "derived curve - isoparametric curve" which has a green dot meaning it's a supported command. It records fine but when I try to play it back the dialog box does not display on screen. Nothing happens. Does anyone no how to get this working...

Thanks John, That was exactly what I was missing. Rick D. Win7 64 bit w/NX9.0.3.4 MP9 and NX10.0.3 Vericut 7.4

Hi All, I'm using the UDE "Set Modes" to change the feederate in a toolpath to FRN from default IPM. Does anyone know a way at the "End of Path" or anywhere in the post to change it back to IPM mode without using the UDE again. The Address G_feed stays G93 after being set in the UDE and I...

I have discovered if the WCS is moved so part is all plus coordinates I do not get "ERROR CREATING FACET BODY". In previous versions this was not the case you would get warning the part has negative coordinates but it would still export the .STL file. Problem remains that if moved from MCS (and...