Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

Register Log in
  • Congratulations KootK on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Drafting Standards, GD&T & Tolerance Analysis

madohman
  • Locked
  • Question
Slotted Spring Pin Position Tolerance?
Replies
0
Views
68
madohman
madohman
engiNERD77
  • Locked
  • Question
Concentricity Gage
Replies
5
Views
298
engiNERD77
engiNERD77
pmarc
  • Locked
  • Question
Tolerance stack question 1
Replies
19
Views
279
bxbzq
bxbzq
SeasonLee
  • Locked
  • Question
Correct way to write the hole size
Replies
0
Views
90
SeasonLee
SeasonLee
tooldeziner
  • Locked
  • Question
When using the Inch standard, is it mandatory to use 3 decimals in the feature frame?
Replies
3
Views
117
KENAT
KENAT
diesel0621
  • Locked
  • Question
Clamp Ring Tolerances
Replies
2
Views
265
diesel0621
diesel0621
SeasonLee
  • Locked
  • Question
Flatness question 3
2
Replies
37
Views
325
Belanger
Belanger
JNieman
  • Locked
  • Question
Symbol Identification Question 2
Replies
8
Views
177
JNieman
JNieman
PeterMcGonigleCRH
  • Locked
  • Question
Zinc Coating Standards Electro-Galvanisation vs Hot Dipped Galvanisation
Replies
1
Views
189
CoryPad
CoryPad
WalkSoftly
  • Locked
  • Question
Quick question
Replies
13
Views
169
WalkSoftly
WalkSoftly
Tunalover
  • Locked
  • Question
Use of composite geometric positional tolerancing on cylindrical surfaces 1
Replies
4
Views
77
Tunalover
Tunalover
SeasonLee
  • Locked
  • Question
Offset tolerance zone of a profile FCF? 1
Replies
2
Views
108
SeasonLee
SeasonLee
fsincox
  • Locked
  • Question
Invoking ASME Y14.100 (again)
Replies
2
Views
222
lwealing
lwealing
Airfix
  • Locked
  • Question
Pitch Diameter as Primary Datum? 1
Replies
12
Views
810
Airfix
Airfix
Dudeman555
  • Locked
  • Question
proper datum callout 1
2
Replies
20
Views
699
SeasonLee
SeasonLee
BrownsFanGodHelpMe
  • Locked
  • Question
"CAD is Master" note 1
Replies
12
Views
766
BrownsFanGodHelpMe
BrownsFanGodHelpMe
gabimo
  • Locked
  • Question
Derived Median Line Straightness and Derived Median Plane Flatness 1
Replies
13
Views
248
greenimi
greenimi
joshpjost
  • Locked
  • Question
Thread Relief Constant
Replies
1
Views
231
CheckerHater
CheckerHater
Storaker
  • Locked
  • Question
Circular Symmetric Parts - General Tolerancing ISO 2768
Replies
19
Views
395
CheckerHater
CheckerHater
Tunalover
  • Locked
  • Question
Invoking ASME Y14.100 1
Replies
9
Views
526
dgallup
dgallup
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top Bottom