Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Boiler and Pressure Vessel engineering

Hande123
  • Locked
  • Question Question
What is meant by FRL?
Replies
3
Views
104
3DDave
3DDave
Tthibodeauxba
  • Locked
  • Question Question
Bleeder Slip Blind Vent Hole Calculation
Replies
0
Views
388
Tthibodeauxba
Tthibodeauxba
Aloni
  • Locked
  • Question Question
pad lug Ring Girder Supports
Replies
4
Views
457
Aloni
Aloni
LIAM_7
  • Locked
  • Question Question
safety factor and linearized stresses
Replies
8
Views
365
LIAM_7
LIAM_7
TheEverest
  • Locked
  • Question Question
Wire Plate
Replies
3
Views
152
r6155
r6155
imrnhdi
  • Locked
  • Question Question
Required Skirt Thickness to withstand Local Bending in PV Elite
Replies
1
Views
328
RAJPT89
RAJPT89
DJPA1234
  • Locked
  • Question Question
SA 240 304 higher vs lower allowabl
Replies
4
Views
257
DriveMeNuts
DriveMeNuts
RAGER
  • Locked
  • Question Question
MANDATORY APPENDIX 20 HUBS MACHINED FROM PLATE
Replies
2
Views
338
RAGER
RAGER
Krausen
  • Locked
  • Question Question
S&T Exchanger - Machining Down Flange Faces
Replies
13
Views
737
r6155
r6155
erkuts
  • Locked
  • Question Question
Etan Cracking furnace tubes failure
Replies
6
Views
331
chicopee
chicopee
Paulettaa
  • Locked
  • Question Question
1 1/4Cr-1/2Mo fabrication as per API 934 C
Replies
17
Views
1K
Drums4Tay
Drums4Tay
Resegone
  • Locked
  • Question Question
ASME 2017 or ASME 2019?
Replies
10
Views
401
XL83NL
XL83NL
TheEverest
  • Locked
  • Question Question
Size of Openings in Skirt
Replies
1
Views
138
r6155
r6155
NMP1306
  • Locked
  • Question Question
Nozzle to Shell Inside Fillet Weld Leg
Replies
4
Views
368
DriveMeNuts
DriveMeNuts
Tomy-Met
  • Locked
  • Question Question
Pipe End Cap Design Thickness
Replies
6
Views
560
KevinNZ
KevinNZ
ElCidCampeador
  • Locked
  • Question Question
PWHT and PFHT for Group 3.1 - EN 13445
Replies
1
Views
451
ElCidCampeador
ElCidCampeador
Mohit_singh
  • Locked
  • Question Question
Most Severe case for Nozzle Load Directions
Replies
5
Views
237
1gibson
1gibson
julian89
  • Locked
  • Question Question
Design of heads with FEA (ASME VIII-2)
Replies
7
Views
374
TGS4
TGS4
DK44
  • Locked
  • Question Question
Design of Tube Sheets with NTIW Tube layout.
Replies
1
Views
161
SnTMan
SnTMan
chiru123pc
  • Locked
  • Question Question
EPDM RUBBER SHEET
Replies
1
Views
180
Latexman
Latexman
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top