Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

Register Log in
  • Congratulations 3DDave on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Boiler and Pressure Vessel engineering

swiss037
  • Locked
  • Question
designing titanium pressure cooker, 2,5 L (85 fl oz), 50 bar (725 psi) and 250¦C (482¦F)
Replies
3
Views
126
moltenmetal
moltenmetal
MikeG7
  • Locked
  • Question
Nozzle neck thickness per UG-45
Replies
3
Views
158
MikeG7
MikeG7
salmon2
  • Locked
  • Question
Elastic-plastic (EP) analysis 3
Replies
5
Views
328
TGS4
TGS4
Masters2788
  • Locked
  • Question
Hydrotest Allowable Stress
Replies
3
Views
233
Masters2788
Masters2788
oosnicram
  • Locked
  • Question
PED 97/23/EC pressure vessel classification
Replies
7
Views
430
europipe
europipe
sxz
  • Locked
  • Question
Material selection for flare stack and seal drum at 425 C degree 2
Replies
3
Views
224
SNORGY
SNORGY
karthik1amar
  • Locked
  • Question
Pv Elite
Replies
1
Views
81
SnTMan
SnTMan
ashaykadam
  • Locked
  • Question
Bolt Spacing in Flange Design for Lethal Service as per ASME Sec-VIII Div-1 Clause 2-5 & 2-6 1
Replies
1
Views
271
SnTMan
SnTMan
mrudulv08
  • Locked
  • Question
Collar Bolt Requirements for Shell and Tube heat Exchangers
Replies
1
Views
292
gr2vessels
gr2vessels
mechyp
  • Locked
  • Question
Post Froming Req. as per UHA-44( for material that not listed in table)
Replies
8
Views
320
mechyp
mechyp
MichalB
  • Locked
  • Question
proper nomenclature - WHRSG or WHRB
Replies
3
Views
188
dougarthur42
dougarthur42
mlh77
  • Locked
  • Question
Pressure vessel
Replies
4
Views
121
GenB
GenB
iosale
  • Locked
  • Question
Appendix 28 ASME VIII
Replies
0
Views
122
iosale
iosale
Inki
  • Locked
  • Question
Cone to cone junction rings when you have a cone shell with different thicknesses at External Pressu
Replies
3
Views
208
SnTMan
SnTMan
APItips
  • Locked
  • Question
Hydraulic test pressure of Tube bundle as per TEMA R
Replies
1
Views
172
SnTMan
SnTMan
bijapur1981
  • Locked
  • Question
ASME Sec 8 Div 1 Vessel 4:1 Transition Head to Shell is not done 1
Replies
3
Views
168
GenB
GenB
791Medley
  • Locked
  • Question
Inspector
Replies
5
Views
153
chicopee
chicopee
ChemEngSquirrel
  • Locked
  • Question
Design Pressure Selection
Replies
4
Views
220
JStephen
JStephen
UserAK
  • Locked
  • Question
surface roughness on tube hole?
Replies
3
Views
268
muld0020
muld0020
APItips
  • Locked
  • Question
Calculation of retirement thickness for a furnace tube
Replies
5
Views
359
chicopee
chicopee
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top Bottom