Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations JStephen on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Boiler and Pressure Vessel engineering

Ryan DelaCourt
  • Locked
  • Question Question
Calculating Total Required Valve closing torque for Butterfly Valve
Replies
2
Views
431
Ryan DelaCourt
Ryan DelaCourt
vonz33
  • Locked
  • Question Question
Find the flaw on this design
2
Replies
27
Views
651
LittleInch
LittleInch
vinothsvk
  • Locked
  • Question Question
UW-3 Weld joint category
Replies
6
Views
792
vinothsvk
vinothsvk
loilfan
  • Locked
  • Question Question
Head Forming Table
Replies
11
Views
283
r6155
r6155
FoxRox
  • Locked
  • Question Question
ASME BPVC Sec VIII Div 2 Part 5 Training
Replies
2
Views
194
FoxRox
FoxRox
Ryan DelaCourt
  • Locked
  • Question Question
Butterfly Disc Vessel and Pressure analysis.
Replies
0
Views
85
Ryan DelaCourt
Ryan DelaCourt
jakov11000
  • Locked
  • Question Question
UG-101 (p)
Replies
7
Views
398
jakov11000
jakov11000
AhmedDeiaa
  • Locked
  • Question Question
Need any one have an experience in dish end machining ?
Replies
2
Views
172
Don56
Don56
JG MechEng
  • Locked
  • Question Question
Damaged flange facing - should this get repaired or replaced
Replies
5
Views
1K
r6155
r6155
jtseng123
  • Locked
  • Question Question
Material for insulation support ring and lifting lug at low temperature service
Replies
5
Views
306
TGS4
TGS4
vermatron
  • Locked
  • Question Question
Design Sec.VIII div.2 vessel using a material not listed in Sec.II
Replies
3
Views
640
TGS4
TGS4
countallloss
  • Locked
  • Question Question
Is an ASME stamp requried?
Replies
5
Views
2K
fs_longhorn
fs_longhorn
ElCidCampeador
  • Locked
  • Question Question
Standard Flange EN 1092 for PED
Replies
1
Views
256
XL83NL
XL83NL
dcattoni
  • Locked
  • Question Question
Design of saddle
Replies
3
Views
157
PMCap
PMCap
Seixas
  • Locked
  • Question Question
In 2004 croy2 posted this question:
Replies
0
Views
65
Seixas
Seixas
TylerM
  • Locked
  • Question Question
ASME BPVC Section II Part D
Replies
7
Views
1K
TylerM
TylerM
Eng822
  • Locked
  • Question Question
Customer wants 1500 flange but code requires 2500#
Replies
7
Views
205
Eng822
Eng822
blackegl
  • Locked
  • Question Question
Welding on ASME B31.3 PWHT Component Requirements
Replies
6
Views
784
DekDee
DekDee
Peter--man
  • Locked
  • Question Question
Tube/Tubesheet welding; min. Leak Path
Replies
0
Views
160
Peter--man
Peter--man
TylerM
  • Locked
  • Question Question
Ellipsoidal head with ts/L < 0.002
Replies
4
Views
369
r6155
r6155
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top