Tobalcane,
Yes, I can put eyes on alll four corners, that's my post concern. where to put the eyes the skid be balanced when we lift to move from location to location on a truck.
Dear All
I'm building an oil well measurement system mounted on skid, my doubt: How can I calculate where to put the lifting eyes
and get the right the load distribution when it be lifted whithout deflection.Any software?
Skid is 23,22' x 7,54', all stuff with vessel pipes, instruments, weight...
Dear All
I'm building an oil well measurement system mounted on skid, my doubt: How can I calculate where to put the lifting eyes and get the right the load distribution when it be lifted whithout deflection.Any software?
Skid is 23,22' x 7,54', all stuff with vessel, pipes and instruments...
Gayas,
I advice you to open an office overseas in Brazil due to a lack of vessels company, there are only 5 that are able to produce big ones.
Last year I used to work fo Petrobras Oil Company (petrobras.com.br) and had a lot of troubles wit this kind of companies, mainly with date of delivery...
Kresimir,
I think that all posts are just about chemical compouds that could provide the foulling, and concerns about chemical cleanings, but, in fact, you should have all your tubes not clogged to permit the chemicals flow.
Have you even think of mechanical cleaning?
Luiz Souza
Brazil
Lastone,
Concerning to vertiacal baffles. I've seen it, here, in Brazil and it's supposed be very commom.
Regards
Luiz Souza
Santos Barbosa Company
A Wood Group Brazil Company
www.woodgroup.com
Thanks, Corrosionman,
It's the same here in Brazil. But I'm not quite sure it'll not cause any damage, anyway, it should be a matter for doctors, not for us, I was just worried about.
Best Regards
Luiz Souza
Brazil
luiz.henrique@santosbarbosa.com.br
Wood Group Brasil
www.woodgroup.com
Dear Fellows,
In my country, Brazil, the use of sand for blasting was forbbiden many years ago.Instead of it we're using cooper slag due to competitive price. I think to myself, was not cooper slag as dangerous as sand to our health? Does anyone has some information about?
Also Thanks, mshimko,
But, what kind of non-metallic plugs? It's easier to have on hand CS to produce the plugs, concern to non-metallic, we should keep it as parts.
Thanks once again EdStainless,
You're pretty sure, only some tubes corroded. Tubesheet looks fine. I'll follow your recommendation.
Regards
Luiz Souza
Wood Group Brazil
www.woodgroup.com
Dear Fellows,
At our plant we're experiencing corrosion on ID air-coolers CS tubes, the solution we've found is to plug those tubes with plugs made of the same material of the tubes. My question: Does those plugs will not corrode just like the tubes, as the corrosion cause wasn't still found...
Luis,
Let's suppose your tube is 3/4" O.D., 20' long, depends of the hardness of the coke you've to use a drill and after you've broke the mechanicall resistance it'll gonna 4-5 hr a tube.For full cleaning you need to hydroblasting too.
Hope it helps.
Luiz Souza
Brazil
Dear Fellows,
We’ve a bidding in our gas processing plant for 4 firefighting water tanks, of course no roofs, the contractor winner proposes reduce the welding surface area by using large carbon steel plates than ones on the original designing.
Original: Plate is ¼” thickness x 7.87 ft x...
CARF,
Thank you so much for the soft, but.
Do I can use to calculate head loss from start point to a flare, for example, in a gas piping system? I'm awaiting your reply asap.
TX IN ADVANCE.
I'm not a english native speaker but I'll try explain. We've several gas line, straight ones that has points where we got a psv valve, then we expericed a reduction of gas volume, that's is what we need to calculate and, also need that formula.
friction rate, flow velocity, 2g and so ...
I...