Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: R1H2
  • Order by date
  1. R1H2

    Welding Structural Steel supports for SoCalGas

    I can't say for certain. But I believe that it is.
  2. R1H2

    Welding Structural Steel supports for SoCalGas

    Hi All, Our company is interested in fabricating structural steel supports for a upcoming SoCalGas project. I'm trying to determine what Certifications or Approvals would be required to facilitate this type of work. And any points of contact to get the ball rolling would be greatly appreciated...
  3. R1H2

    Spent Fuel Pool Instrumentation Design

    Gentlemen, Thx much for the input. Racookpe1978, My spider senses & most of the codes I use were telling me the same information. Eng.g will dictate requirments. We politely no bid the work. Thanks as always for the sage advice. R1H2
  4. R1H2

    Spent Fuel Pool Instrumentation Design

    Hello Gentlemen, I am a Welding Inspector. My shop has a potential client that is looking to have us weld components for Spent fuel pool water level instrumentation. I am concerned that we are lacking acceptance criteria. Can anyone provide direction in regards to specs or standards dictating...
  5. R1H2

    Whats the best method for shipping painted components.

    Thanks for the input guys. These forums are invaluable source of info. Even if it's only for sounding board use. Mcgyvr, We've seen the tower packing technique as well. We have resorted to supplying proper boxes to several vendors to reduce this issue. These parts are kraft wrapped &...
  6. R1H2

    Whats the best method for shipping painted components.

    Hi All, We are a job shop with no coating processes in house. So, we outsource our painting & powder coating. Our vendors often assist us by packaging the finished prods. to reduce handling. Several of our customer have recently rejected our prods. for surface scuffs & light scratching...
  7. R1H2

    3/8-16,SS, Hex , 3 proj. weld nut torque

    Hi Guys, 1st, thanks for the replys. Screwman: Its a torque to twist loose. & I agree, Nothing on the PO or Print, then there is nothing to reject against. (To back this up we have a physical sample that they have approved.) Etc., Etc. I have plenty of back-up against any liability. I am...
  8. R1H2

    3/8-16,SS, Hex , 3 proj. weld nut torque

    Hi All, Does anyone have a spec on the designed torque load specs for 3/8-16, Hex, 3 projection, weld nuts? I have a client that has rejected my parts due to the weld nuts failing under torque. We used the Nut MFGs weld specs & did an informal load test. Which seemed to be sufficient, for...
  9. R1H2

    weld design Fillet or. ? ?

    Isaac, Thanks for the reply. I appreciate the input.
  10. R1H2

    weld design Fillet or. ? ?

    I've seen ASME codes define fillet welds as "weld of approx. Triangular cross section joining (two surfaces)..." What if there were a 3rd mat'l sandwiched between the stated "two surfaces" in a lap joint condition? Would this be considered a fillet?
  11. R1H2

    PQR qual for PJP to Sect IX

    Kiwi, Agreed on all points. This will be our action. Only wished I seen this up front. I'll know better next time. Thx for the assist. R.
  12. R1H2

    PQR qual for PJP to Sect IX

    Kiwi,Meteng, Thx for the replies. I interpret 290.5 as applicable specifically to 290 Temper Bead Welding. (No?) QW-451 does not reference removal of unfused joint mat'l prior to test. QW-202 Types of tests require. QW-202.1 refs QW-451 & QW-463. Niether discuss prep of PJP matl's...
  13. R1H2

    PQR qual for PJP to Sect IX

    I'm looking for some clarification on testing a PJP groove, Procedure Qual. To Sect. IX. Sect. IX implies that PJPs can be qualified per Table QW-451. Table QW-451 (in my humble opinion) applies to CJPs only as there is no discussion or direction for macros or removal of unfused base metal...
  14. R1H2

    Assistance with Alum Assoc. Welding Criteria

    I have 2 questions. I am in need of data regarding the Alum. Assoc. Docs AA ASM 35(I believe this is a design Manual.)and AA ADM 1(Perhaps another design Manual). And their application to welding criteria. 1st Question....Do either of these Docs dictate welding Criteria. 2nd...

Part and Inventory Search

Back
Top