tbuelna, the "bar" designation is an artifact of our ERP system - all materials received in lengths are designated "bar" = round, or "square" = square (there are other designations i.e. "hex", "strip" (thick x width), coil, tubing, etc.)
My understanding was free-machining 316 has a smaller...
I have been reviewing materials quoted from a variety of suppliers. With my drawing requiring 316L (Free Machining, Annealed 1.5" Bar) I have received certs indicating minimum yield strength of:
25ksi, 29ksi, 36ksi, 40ksi, 42ksi and 45ksi
How can the same 316L material be so different?
Am I...
Your anodize vendor can try to redip the part but appearance is not so good, usually vendor will want to strip and re-anodize whole which will change part dimensions 0.05-0.2mm. Not handheld touchup I know of...
They should be able to mask the PEM, solution probably has little effect on PEM but...
You have to start with the first folder, you cannot jump to the server directly in UNC.
Try:
\\ServerName\@Engin~1
maybe look at variations of the folder too "Engine~1" or "@Engin~2" they should be eight character long and end in '~' and a number.
We have corporate rule to have no special characters or spaces in our naming system to avoid this type of issue...no help to you I know.
Can you access the file in a CMD window by typing the UNC path and name? If not try change directory then directory list for each level, this should show...
What is definition of "best"? Most powerful, lightest weight, most energy efficient, meets VDE CSA UL, cheapest, highest thermal efficiency? Too many possible to list.
For machine tools we use combinations of power density and thermal effects, with cost being last factor.
There are 100 ways...
I have worked with smaller companies that do exactly this Londonderry:
ITEM QTY PART NUMBER DESCRIPTION
1 1 4000272 MIRROR
2 1 4000269 MIRROR GASKET
3 1 4000332 MIRROR COVER
4 2 4000624 SPRING ANCHOR
5 1...
I have a part which is a thin metal panel having a label applied. Due to source of part being of lower quality than price, label is often misapplied.
I take label.ai file and place on the solid, but this does not show on the drawing. Is this possible? My workaround is to place label.ai on...
Ed,
What would be the upper temp limit your recommend for galvanized? Would that be better than a stainless at the same temperature range?
Thanks,
Alex
If changing to a closed-loop cooling system, look at using a laser or welder chiller (refrigeration type cooler) instead of ambient radiator. You then set the water temperature just above condensation temperature (not to make water in the bearings) and remove more heat this way.
You might also check into protection requirements set by your laws. I know of some locales that have voltage differntial and duration before trip limits that must be applied to new machinery...
The fluid can be between 0 and +70 degrees celsius, though normal conditions would be 0 to 15 degrees celsius. Because of heat transfer requirements plastics are not on option.
Would you suggest 2205?
The part is minimal loaded, we are looking for 1-2 bar differential pressure integrity only...
Though they would never tell you, the guy mounting the antenna 20 years ago probably told the shop foreman "Hey these two bolts are too short", then went and put in a couple longer ones he had in his toolbox left over from working on his neighbors' car.
The six month process with 30+ engineers...
It will be a housing for mounting magnetic detectors and associated electronics. One surface will be in direct contact with the solution, while the others will be exposed only to air. Titanium or Hastelloy-C are possible but I was hoping for a less expensive option.
The tables I have show 316...
I am looking for a recommendation for materials for long-term direct contact with saturated NaCl. While 316 is "compatabile" I am wondering about long (3-5yrs) contact. We could coat or otherwise improve the surface but the costs must be considered. Any suggestions?
